Component guide · Advanced · 3 min read
Acconeer A111 (SparkFun Breakout)

and A121 (Waveshare Module) 60 GHz Pulsed Coherent Radar Sensors
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Acconeer A111 and A121 are tiny 60 GHz pulsed coherent radars that measure distance to millimetre precision and sense presence, breathing, gestures and liquid level through plastic. The SparkFun A111 breakout uses SPI; the Waveshare A121 module adds a microcontroller with UART, I2C and GPIO. Acconeer's free Exploration Tool lets you see the radar data on a PC.
Key specs at a glance
- Frequency
- 60 GHz pulsed coherent radar
- Range
- Up to about 2 m (A111), up to about 20 m (A121)
- Precision
- Millimetre-level distance
- Interface
- SPI (A111); UART, I2C, GPIO (Waveshare A121)
- Power
- Very low, suits battery devices
- Uses
- Distance, presence, breathing, level, parking, gestures
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
What the Acconeer A111 and A121 60 GHz pulsed radar is
The Acconeer A111 and A121 are tiny 60 GHz pulsed coherent radar chips that measure distance very precisely and sense motion, breathing and level through plastic.
Pulsed coherent radar sends short pulses and tracks the phase of the echo, which gives very fine distance resolution and the ability to see tiny movements.
Start with the Exploration Tool to pick a detector (distance, presence, breathing), then run that detector on the module.
Acconeer A111 and A121 60 GHz pulsed radar pinout
The pins on the Acconeer A111 and A121 60 GHz pulsed radar and what each one does.
| Pin | Function |
|---|---|
| VIN / 3V3 | Supply |
| GND | Ground |
| SPI | SCK, MOSI, MISO, CS (A111) |
| TX / RX or SDA / SCL | Waveshare A121 |
| GPIO | Presence or threshold output |
- VIN / 3V3
- Supply
- GND
- Ground
- SPI
- SCK, MOSI, MISO, CS (A111)
- TX / RX or SDA / SCL
- Waveshare A121
- GPIO
- Presence or threshold output
Wiring the Acconeer A111 and A121 60 GHz pulsed radar
Connect the Acconeer A111 and A121 60 GHz pulsed radar like this.
| Acconeer A111 and A121 60 GHz pulsed radar pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5 V | 5 V (VIN) or 3.3 V (check module) |
| GND | GND | GND |
| Radar TX | D10 (SoftwareSerial RX, low baud only) | GPIO 16 (RX2) |
| Radar RX | D11 | GPIO 17 (TX2) |
| OUT (if fitted) | D2 | GPIO 27 |
- VCC
- Arduino Uno:
- 5 V
- ESP32:
- 5 V (VIN) or 3.3 V (check module)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- Radar TX
- Arduino Uno:
- D10 (SoftwareSerial RX, low baud only)
- ESP32:
- GPIO 16 (RX2)
- Radar RX
- Arduino Uno:
- D11
- ESP32:
- GPIO 17 (TX2)
- OUT (if fitted)
- Arduino Uno:
- D2
- ESP32:
- GPIO 27
Example code
This needs the module running Acconeer's exploration server firmware; the A111 uses the older a111 tools.
# pip install acconeer-exptool
from acconeer.exptool import a121
client = a121.Client.open(serial_port="COM5") # or /dev/ttyUSB0
sensor_config = a121.SensorConfig(start_point=50, num_points=100, step_length=2)
client.setup_session(sensor_config)
client.start_session()
for _ in range(20):
result = client.get_next()
print(abs(result.frame).max(axis=1)) # echo strength per sweep
client.stop_session()
client.close()Setup and tuning
connect the board to a PC and try the distance and presence detectors before writing your own code.
distance, presence, breathing, tank level and parking each have their own tuned settings.
put the sensor behind a thin plastic window with no metal in front. Keep the window at a distance the maker recommends.
use a clean 3.3 V supply; the A121 Waveshare module also accepts its own supply input.
run the detector's calibration with the empty scene first so fixed objects are removed from the result.
What you need
Shop this list5 of 5 found in our store · ₹14,741
SparkFun Pulsed Radar Breakout – A111, SEN-16826 – 60 GHz PCR Sensor with SPI Interface: the part this guide coversSparkFun Pulsed Radar Breakout – A111, SEN-16826 – 60 GHz PCR Sensor with SPI Interface₹9,209
Waveshare A121 60GHz mmWave Radar Module, High-Precision PCR – UART/I2C/GPIO Interface: another version this guide coversWaveshare A121 60GHz mmWave Radar Module, High-Precision PCR – UART/I2C/GPIO Interface₹2,729
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
Benewake TF-Luna micro LiDAR: a laser alternative for short rangeBenewake TF-LUNA Micro LiDAR Distance Sensor (Range: 0.2m~8m) – UART/I2C Interface₹2,329Closest match, check the specs
Alternatives and when to choose them
- ToF sensors: laser distance, cheaper.
- Radar level sensors: ready-made tank units.
- Vital sign radars: ready breathing output.
Common mistakes to avoid
- Mounting the sensor behind a metal or painted metallic cover.
- Skipping calibration, so fixed objects show up as targets.
- Using one detector's settings for a different task.
- Feeding it from a noisy supply shared with motors.
Frequently asked questions
Can the A121 see through walls?
It can see through thin plastic, glass and fabric, but not through metal, and thick walls weaken it a lot.
How accurate is the distance reading?
In good conditions it measures distance to about a millimetre, much finer than ultrasonic or IR sensors.
Can it detect a person sitting still?
Yes. The presence detector picks up the small motion of breathing, so a still person is still detected.
Does it work with Arduino?
The SparkFun A111 board has Arduino examples over SPI, and the Waveshare A121 module gives results over UART or I2C to any board.
Is 60 GHz radar safe?
Yes. The output power is very low, similar to other short-range consumer radars.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
