Component guide · Intermediate · 4 min read
Autopilot Accessories

Pixhawk I2C Expansion Boards, DroneCAN Hubs, Safety Switch, Buzzer and LED, PPM Encoder, MinimOSD, Holybro Micro OSD, Naza LED and Receiver Cables
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These small parts complete an autopilot build. I2C expansion boards let you connect several I2C devices (compass, airspeed, rangefinder) to one port; CAN hubs do the same for DroneCAN. The safety switch and buzzer are required to arm a Pixhawk; the PPM encoder converts PWM receiver outputs to one PPM line; and MinimOSD boards overlay flight data on analog FPV video.
Key specs at a glance
- I2C hubs
- 4 to 6 ports, Pixhawk DF13 or JST-GH
- CAN hubs
- 4 to 12 ports, powered on SwiftCAN
- PPM encoder
- 8 PWM in, 1 PPM out
- OSD
- MAX7456 MinimOSD, Holybro Micro OSD V2
- Switches
- Safety switch, LED switch, e-switch
- Cables
- CC3D and Naze32 receiver looms
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Pixhawk I2C Port Expand Board with Cable₹239
Option 2Pixhawk I2C Port Expand Board with Cable – Black₹149
Option 3RadioLink I2C Expansion Board for Flight Controllers₹474
Option 4Jiyi CAN HUB-12 Flight Control CAN Expansion Module₹6,799
Option 5SwiftCAN-HUB 6-Port Powered CAN Hub for ArduPilot, PX4, DroneCAN₹4,910
Option 6Pixhawk LED Switch₹439
What the Autopilot accessories: I2C hubs, CAN hubs, switches, PPM encoders, OSDs and cables is
These small parts complete a Pixhawk or flight-controller build: I2C and CAN hubs, safety switches, buzzers, PPM encoders and on-screen display boards.
Match the connector type (DF13 on older Pixhawks, JST-GH on newer ones). MinimOSD boards need the MAVLink stream from a telemetry port; flash the MWOSD or ArduCAM OSD firmware.
The OpenLog blackbox recorder logs Naze32/F3 flight data to a microSD card for tuning.
Autopilot accessories: I2C hubs, CAN hubs, switches, PPM encoders, OSDs and cables pinout
The pins on the Autopilot accessories: I2C hubs, CAN hubs, switches, PPM encoders, OSDs and cables and what each one does.
| Pin | Function |
|---|---|
| I2C | SDA, SCL, 5V, GND |
| CAN | CAN_H, CAN_L, 5V, GND |
| PPM | Signal, 5V, GND to RC IN |
| OSD | TELEM TX/RX in, video in and out |
- I2C
- SDA, SCL, 5V, GND
- CAN
- CAN_H, CAN_L, 5V, GND
- PPM
- Signal, 5V, GND to RC IN
- OSD
- TELEM TX/RX in, video in and out
Wiring the Autopilot accessories: I2C hubs, CAN hubs, switches, PPM encoders, OSDs and cables
Check pin order on every cable; DF13 and JST-GH leads from different makers are not always wired the same way.
| Autopilot accessories: I2C hubs, CAN hubs, switches, PPM encoders, OSDs and cables pin | Connection | Note |
|---|---|---|
| I2C hub | FC I2C port | Each device needs a unique address |
| CAN hub | FC CAN1 | Terminate the bus ends |
| PPM encoder | Receiver outputs to encoder, encoder to RC IN | Set protocol to PPM |
| OSD | TELEM port and camera/VTX video | MAVLink baud 57600 |
- I2C hub
- Connection:
- FC I2C port
- Note:
- Each device needs a unique address
- CAN hub
- Connection:
- FC CAN1
- Note:
- Terminate the bus ends
- PPM encoder
- Connection:
- Receiver outputs to encoder, encoder to RC IN
- Note:
- Set protocol to PPM
- OSD
- Connection:
- TELEM port and camera/VTX video
- Note:
- MAVLink baud 57600
Example code
After adding I2C devices, run i2c scan style checks in the Mission Planner messages tab or look for the device in the hardware ID list.
BRD_SAFETYENABLE = 1 # safety switch required (0 to disable)
NTF_BUZZ_TYPES = 1 # buzzer on
CAN_P1_DRIVER = 1 # enable CAN1 for DroneCAN devices
CAN_D1_PROTOCOL = 1 # DroneCAN
SERIAL2_PROTOCOL = 2 # MAVLink2 on TELEM2 for MinimOSD
SERIAL2_BAUD = 57 # 57600 baud
RC_PROTOCOLS = 1 # all; or set PPM onlySetup and tuning
connect both to the Pixhawk's dedicated ports; ArduPilot and PX4 expect them unless disabled.
check each device's address; two devices with the same address cannot share the hub.
terminate the two ends of the CAN bus and set unique node IDs for DroneCAN devices.
connect receiver channels in order and set the radio type to PPM in the autopilot.
flash the matching firmware to MinimOSD boards and connect video in and out through it.
What you need
Shop this list20 of 20 found in our store · ₹41,568
Pixhawk I2C Port Expand Board with Cable: the part this guide coversPixhawk I2C Port Expand Board with Cable₹239
Pixhawk I2C Port Expand Board with Cable – Black: another version this guide coversPixhawk I2C Port Expand Board with Cable – Black₹149
RadioLink I2C Expansion Board for Flight Controllers: another version this guide coversRadioLink I2C Expansion Board for Flight Controllers₹474
Jiyi CAN HUB-12 Flight Control CAN Expansion Module: another version this guide coversJiyi CAN HUB-12 Flight Control CAN Expansion Module₹6,799
SwiftCAN-HUB 6-Port Powered CAN Hub for ArduPilot, PX4, DroneCAN: another version this guide coversSwiftCAN-HUB 6-Port Powered CAN Hub for ArduPilot, PX4, DroneCAN₹4,910
Generic Pixhawk LED Switch: another version this guide coversPixhawk LED Switch₹439
Pixhawk Passive Buzzer and Switch Module: another version this guide coversPixhawk Passive Buzzer and Switch Module₹549
ReadyToSky Safety E-Switch: another version this guide coversReadyToSky Safety E-Switch₹359
Generic Pixhawk PPM Encoder Module: another version this guide coversPixhawk PPM Encoder Module₹689
Mini OSD FOR APM 2.6/2.8: another version this guide coversMini OSD FOR APM 2.6/2.8₹1,043
Mini OSD for Pixhawk Flight Controller Module: another version this guide coversMini OSD for Pixhawk Flight Controller Module₹1,369
Holybro Micro OSD V2 – Standard Set: another version this guide coversHolybro Micro OSD V2 – Standard Set₹2,689
Tarot Pixhawk Power Monitor Module TL3401: another version this guide coversTarot Pixhawk Power Monitor Module TL3401₹2,550
T-Motor DATA LINK V2 – Flight Controller Accessory: another version this guide coversT-Motor DATA LINK V2 – Flight Controller Accessory₹17,189
DJI NAZA M-Lite Remote LED Module: another version this guide coversDJI NAZA M-Lite Remote LED Module₹524
DJI NAZA V2 Remote LED Module: another version this guide coversDJI NAZA V2 Remote LED Module₹499
CC3D Receiver Cable: another version this guide coversCC3D Receiver Cable₹139
Generic NAZE32 Receiver Cable: another version this guide coversNAZE32 Receiver Cable₹119
Generic Naze 32 6DOF Receiver Cable: another version this guide coversNaze 32 6DOF Receiver Cable₹125
GY-Openlog Cleanflight Naze32 F3 Blackbox Flash Recorder: another version this guide coversGY-Openlog Cleanflight Naze32 F3 Blackbox Flash Recorder₹715
Alternatives and when to choose them
- Pixhawk 6X and 6C: the autopilots.
- Telemetry radios: ground link.
- Airspeed and telemetry sensors: I2C sensors.
Common mistakes to avoid
- Putting two I2C devices with the same address on one hub.
- Leaving the CAN bus without termination.
- Mixing up receiver channel order on the PPM encoder.
- Flashing the wrong firmware to a MinimOSD board.
Frequently asked questions
Do I need the safety switch?
ArduPilot and PX4 expect it by default. You can disable it in parameters, but it is a useful safety step.
Why use an I2C expansion board?
It lets several I2C devices, such as a compass and airspeed sensor, connect to one Pixhawk I2C port.
What does a PPM encoder do?
It combines up to 8 PWM receiver channels into one PPM signal for flight controllers with a single input.
Can I use MinimOSD with a modern flight controller?
It works with older setups; most new flight controllers have a built-in OSD chip.
Why is my DroneCAN device not detected?
Check the termination, the node ID and that CAN is enabled in the autopilot parameters.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



