How-to · Advanced · 3 min read
Airspeed and Telemetry Sensors for Drones and Planes
Pitot Tubes, DroneCAN and Current Sensors
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Fixed-wing and VTOL aircraft need airspeed, not just GPS speed, to avoid stalls. A pitot tube feeds a differential pressure sensor that the autopilot reads over I2C or DroneCAN. Mount the pitot in clean air away from the propeller, calibrate it on the ground, and add current, RPM and temperature sensors for telemetry that tells you about battery and motor health.
Key specs at a glance
- Airspeed
- Digital pitot sensors and CUAV SKYE DroneCAN
- Interfaces
- I2C, DroneCAN (CAN)
- Current sensing
- Hall sensors such as 50 A UAV modules
- Telemetry sensors
- FrSky Smart Port RPM and temperature
- Data link
- Hobbywing Data Link for ESC settings
- Autopilots
- ArduPilot and PX4
Why airspeed
GPS gives speed over ground. In wind this can be very different from speed through the air. A plane at low airspeed with a tailwind can stall while GPS speed looks fine. Airspeed sensors let the autopilot hold safe speeds, calculate wind and transition VTOLs correctly.
Types of sensor
Choose by autopilot connection.
| Sensor | Connection | Notes |
|---|---|---|
| Digital pitot sensor (Holybro) | I2C | Simple plug-in with a pitot tube |
| CUAV SKYE / SKYE 2 | DroneCAN | Works well on long cable runs |
| Current sensor (HUB-E 50A) | Analog | Measures battery current |
| RPM and temperature sensor (FrSky) | Smart Port | For telemetry to your radio |
| Hobbywing Data Link | USB/UART | Configure and log ESC data |
- Digital pitot sensor (Holybro)
- Connection:
- I2C
- Notes:
- Simple plug-in with a pitot tube
- CUAV SKYE / SKYE 2
- Connection:
- DroneCAN
- Notes:
- Works well on long cable runs
- Current sensor (HUB-E 50A)
- Connection:
- Analog
- Notes:
- Measures battery current
- RPM and temperature sensor (FrSky)
- Connection:
- Smart Port
- Notes:
- For telemetry to your radio
- Hobbywing Data Link
- Connection:
- USB/UART
- Notes:
- Configure and log ESC data
Mounting a pitot tube
1. Put the pitot tube on a wing or boom in clean airflow, out of the propeller wash. 2. Point it exactly along the airflow. 3. Use short silicone tubing and avoid kinks or leaks. 4. Keep the sensor board inside the airframe and away from heat. 5. Keep water out with a cover on the ground. See Pixhawk and ArduPilot for the autopilot connection.
Calibration
Cover the pitot tube from the wind and run the airspeed calibration in the ground station so the sensor learns its zero. Check the reading at rest, then wave the aircraft through the air in a safe setting. Set the stall speed and minimum airspeed parameters for your aircraft. Pressure basics are in MEMS pressure sensors.
Battery, motor and ESC telemetry
A current sensor and voltage divider show battery use; see PDB and BEC and LiPo for drones. RPM and temperature sensors tell you about the motor, and data links read ESC logs. Send these values to the radio with telemetry radios or the receiver link.
Try it: Pressure converter calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Placing the pitot tube in propeller wash.
- Skipping airspeed calibration.
- Leaving a cover on the pitot in flight.
- Using long tubing with leaks.
- Ignoring a current sensor's rated limit.
Frequently asked questions
Do I need airspeed for a quadcopter?
No. It is for planes and VTOL aircraft.
What is DroneCAN?
A robust CAN-based protocol for autopilot peripherals.
How do I calibrate a pitot?
Cover it from the wind and run the autopilot's calibration routine.
Can I use GPS speed instead?
Not safely in wind.
What current sensor range do I need?
Higher than the maximum current you expect.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






