Component guide · Beginner · 4 min read
ESP32 E-Paper Boards

Waveshare ESP32-S3 and ESP32-C6 1.54 Inch, Elecrow CrowPanel 4.2 Inch, AI-Thinker AiPi-ESL 2.13 Inch and NFC-Powered 4.2 Inch Kit
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
E-paper keeps its image with no power, so these boards make weather stations, shelf labels, name badges and calendars that run for months on a battery. The Waveshare 1.54 inch boards add an ESP32-S3 or ESP32-C6 with sensors and touch on some; the Elecrow CrowPanel is a 4.2 inch HMI with buttons; the AiPi-ESL is a Bluetooth shelf label; and the NFC kit is powered and updated by a phone tap.
Key specs at a glance
- Screens
- 1.54, 2.13 and 4.2 inch black/white (some red)
- Controllers
- ESP32-S3, ESP32-C6, BL602/BL618, or NFC-only
- Refresh
- 1 to 3 s full, faster partial on supported panels
- Power
- Deep sleep in microamps between updates
- Extras
- SHTC3 sensor, RTC, touch, buttons, battery charger (model dependent)
- Software
- GxEPD2, ESP-IDF, ESPHome, phone app (NFC)
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Waveshare ESP32-S3 1.54-Inch e-Paper AIoT Development Board₹2,239
Option 2Waveshare ESP32-S3 1.54-Inch e-Paper AIoT Dev Board w/ Touch₹2,679
Option 3Waveshare ESP32-S3 1.54-Inch e-Paper AIoT Development Board, Black / White without Touch Control₹3,619
Option 4Waveshare ESP32-C6 1.54-Inch e-Paper AIoT Dev Board₹2,109
Option 5Elecrow CrowPanel ESP32 4.2 Inch E-Paper HMI Display, 400x300₹3,212
Option 6AI-Thinker AiPi-ESL 2.13-inch E-Paper Display w/ Bluetooth₹769
What the ESP32 e-paper development boards and NFC e-paper is
ESP32 e-paper boards combine an ESP32 with an e-ink display that keeps its image with no power, ideal for battery dashboards, labels and weather screens.
Update the screen, then put the ESP32 into deep sleep; the image stays. Avoid full refreshes every few seconds; e-paper is for slow-changing information.
The NFC-powered kit has no battery at all: a phone app sends the image and the energy over NFC.
ESP32 e-paper development boards and NFC e-paper pinout
The pins on the ESP32 e-paper development boards and NFC e-paper and what each one does.
| Pin | Function |
|---|---|
| USB-C | Power, flashing and serial (native USB on S3/C6/RP2350) |
| Display interface | SPI, QSPI, RGB parallel or MIPI to the built-in screen |
| BUSY / RST / DC | E-paper control lines (already wired) |
| Buttons and sensors | On CrowPanel and Waveshare boards |
- USB-C
- Power, flashing and serial (native USB on S3/C6/RP2350)
- Display interface
- SPI, QSPI, RGB parallel or MIPI to the built-in screen
- BUSY / RST / DC
- E-paper control lines (already wired)
- Buttons and sensors
- On CrowPanel and Waveshare boards
Wiring the ESP32 e-paper development boards and NFC e-paper
Do not leave e-paper in a half-refreshed state for long or power it from a sagging supply; always finish the refresh, then put the panel to sleep.
| ESP32 e-paper development boards and NFC e-paper pin | Connection | Note |
|---|---|---|
| USB-C | To a PC to flash | Hold BOOT if not detected |
| Battery | JST LiPo connector where fitted | 3.7V single cell only |
| Sensors | I2C pads or header | 3.3V logic |
- USB-C
- Connection:
- To a PC to flash
- Note:
- Hold BOOT if not detected
- Battery
- Connection:
- JST LiPo connector where fitted
- Note:
- 3.7V single cell only
- Sensors
- Connection:
- I2C pads or header
- Note:
- 3.3V logic
Example code
Choose the GxEPD2 class that matches your panel (the wiki lists it). Elecrow and AI-Thinker boards come with their own examples.
#include <GxEPD2_BW.h>
#include <Fonts/FreeSansBold18pt7b.h>
// Pins from the board wiki: CS, DC, RST, BUSY
GxEPD2_BW<GxEPD2_154_D67, GxEPD2_154_D67::HEIGHT> epd(GxEPD2_154_D67(10, 13, 14, 15));
void setup() {
epd.init(115200);
epd.setRotation(1);
epd.setFont(&FreeSansBold18pt7b);
epd.setFullWindow();
epd.firstPage();
do {
epd.fillScreen(GxEPD_WHITE);
epd.setCursor(10, 60);
epd.print("24.5 C");
} while (epd.nextPage());
epd.hibernate();
esp_sleep_enable_timer_wakeup(15ULL * 60 * 1000000); // 15 minutes
esp_deep_sleep_start();
}
void loop() {}Setup and tuning
use GxEPD2 and pick the class that matches your exact panel size and controller.
the panel uses SPI plus BUSY, RST and DC pins; check the board pin map in the vendor docs.
full refresh flashes and takes 1 to 3 s; use partial refresh for small updates if the panel supports it.
update, then put the ESP32 into deep sleep; the screen keeps the image.
many boards have a panel power pin; switch it off before sleep.
What you need
Shop this list9 of 9 found in our store · ₹17,995
Waveshare ESP32-S3 1.54-Inch e-Paper AIoT Development Board: the part this guide coversWaveshare ESP32-S3 1.54-Inch e-Paper AIoT Development Board₹2,239
Waveshare ESP32-S3 1.54-Inch e-Paper AIoT Dev Board w/ Touch: another version this guide coversWaveshare ESP32-S3 1.54-Inch e-Paper AIoT Dev Board w/ Touch₹2,679
Waveshare ESP32-S3 1.54-Inch e-Paper AIoT Development Board, Black / White without Touch Control: another version this guide coversWaveshare ESP32-S3 1.54-Inch e-Paper AIoT Development Board₹2,239
Waveshare ESP32-C6 1.54-Inch e-Paper AIoT Dev Board: another version this guide coversWaveshare ESP32-C6 1.54-Inch e-Paper AIoT Dev Board₹2,109
Elecrow CrowPanel ESP32 4.2 Inch E-Paper HMI Display, 400x300: another version this guide coversElecrow CrowPanel ESP32 4.2 Inch E-Paper HMI Display, 400x300₹3,212
AI-Thinker AiPi-ESL 2.13-inch E-Paper Display w/ Bluetooth: another version this guide coversAI-Thinker AiPi-ESL 2.13-inch E-Paper Display w/ Bluetooth₹769
Waveshare NFC-Powered e-Paper: another version this guide coversWaveshare NFC-Powered e-Paper₹3,300
USB-C cable: for power, flashing and the serial monitorArduino USB-C to USB-C Cable w/ USB-A Adapter₹1,059Closest match, check the specs
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Alternatives and when to choose them
- Waveshare e-paper modules: screens without an MCU.
- Small ESP32-S3 display boards: colour LCD.
- ESP32-C6 boards: the chip on its own.
Common mistakes to avoid
- Choosing the wrong GxEPD2 class for the panel.
- Only using partial refresh, so ghosting builds up.
- Keeping the ESP32 awake between updates.
- Leaving the panel in direct sun or heat, which can damage it.
Frequently asked questions
Why does my e-paper screen stay blank?
The wrong GxEPD2 display class or pin map is selected. Match the panel model exactly.
Does the display need power to keep the image?
No. E-paper keeps the last image with no power at all.
How often can I refresh the screen?
Partial refresh can run often; do a full refresh every few updates to clear ghosting.
Can e-paper show colours?
Some panels show red or yellow too, but tri-colour refresh takes 10 to 20 s.
How long can it run on a battery?
With deep sleep and hourly updates, many boards run for weeks or months.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

