Component guide · Beginner · 6 min read
RC Plane ESCs

Hobbywing Skywalker 20A to 100A, Surpass Hobby 20A to 100A, SunnySky X65A to X155A and Scorpion Tribunus II
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Fixed-wing ESCs drive the propeller motor of an RC plane and power the receiver and servos through a built-in BEC (UBEC or SBEC). They have plane features such as a brake for folding props, soft start and low-voltage cut-off. Hobbywing Skywalker and Surpass Hobby are popular for trainers and gliders; SunnySky X and Scorpion units suit bigger and faster models.
Key specs at a glance
- Current
- 20A to 155A continuous
- Voltage
- 2S to 8S LiPo
- BEC
- 5V or 6V, 2A to 8A switching
- Features
- Brake, soft start, low-voltage cut-off, timing
- Programming
- Transmitter stick or programming card
- Connectors
- Bullet motor plugs, bare or XT60 battery lead
This part can carry many amps. Use wire thick enough for the current, put a fuse close to the battery, check that connectors are rated for the load and give drivers and motors room to cool. A short at these currents melts wires in seconds.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Hobbywing Skywalker 20A UBEC ESC₹1,199
Option 2Hobbywing Skywalker 30A UBEC ESC₹1,529
Option 3Hobbywing Skywalker 40A Brushless ESC₹1,439
Option 4Hobbywing Skywalker 50A UBEC Brushless ESC₹2,299
Option 5Hobbywing Skywalker-60A UBEC ESC 3-6S LiPo₹2,849
Option 6Hobbywing Skywalker 80A UBEC Brushless ESC 3-6S₹4,289
What the RC plane and fixed-wing ESCs with BEC is
Fixed-wing ESCs with a BEC drive a brushless motor from a LiPo and also supply 5 or 6 V to the receiver and servos, so a plane needs only one flight battery.
Size the ESC 20 to 30% above the motor's maximum current. Check the BEC current against the servos: a 3A BEC is fine for four 9g servos, but larger models with metal-gear servos need 5A or more.
Turn the brake on for folding props and off for fixed props.
RC plane and fixed-wing ESCs with BEC pinout
The pins on the RC plane and fixed-wing ESCs with BEC and what each one does.
| Pin | Function |
|---|---|
| Battery leads | Red + and black - to the battery or PDB |
| Motor wires (3) | To the brushless motor in any order |
| Signal cable | White/yellow signal, black/brown ground, red BEC 5V |
| BEC | Built-in 5V or 6V supply for receiver and servos |
- Battery leads
- Red + and black - to the battery or PDB
- Motor wires (3)
- To the brushless motor in any order
- Signal cable
- White/yellow signal, black/brown ground, red BEC 5V
- BEC
- Built-in 5V or 6V supply for receiver and servos
Wiring the RC plane and fixed-wing ESCs with BEC
Plug the ESC signal lead into the throttle channel of the receiver. Range-check the radio with the motor running before the first flight.
| RC plane and fixed-wing ESCs with BEC pin | Connection | Note |
|---|---|---|
| Battery | Battery or PDB | Check polarity twice |
| Signal | Receiver throttle channel or FC output | Signal plus GND |
| Motor | Three wires, any order | Swap two to reverse |
| Servos | Powered from the receiver via the BEC | Check BEC amps |
- Battery
- Connection:
- Battery or PDB
- Note:
- Check polarity twice
- Signal
- Connection:
- Receiver throttle channel or FC output
- Note:
- Signal plus GND
- Motor
- Connection:
- Three wires, any order
- Note:
- Swap two to reverse
- Servos
- Connection:
- Powered from the receiver via the BEC
- Note:
- Check BEC amps
Example code
Most planes need no code: the receiver drives the ESC. Use stick programming (full throttle at power-on, follow the beep table) to set brake, cut-off and timing.
#include <Servo.h>
Servo esc;
void setup() {
Serial.begin(115200);
esc.attach(9, 1000, 2000);
// Calibration: full throttle at power-up, then low
esc.writeMicroseconds(2000);
Serial.println("Connect the battery now, wait for beeps");
delay(5000);
esc.writeMicroseconds(1000);
delay(4000); // ESC confirms range
}
void loop() {
for (int us = 1000; us <= 1300; us += 10) { esc.writeMicroseconds(us); delay(50); }
delay(2000);
esc.writeMicroseconds(1000);
delay(3000);
}Setup and tuning
pick an ESC rated at least 20 % above the motor's full-throttle current, measured with a watt meter.
linear BECs suit 2 to 3 small servos on 2S to 3S; for 4 or more servos or 4S and up, use a switching BEC.
three motor wires to the motor, the servo lead to the receiver throttle channel, and red and black to the battery with the right connector.
power up with throttle at full, wait for the beeps, then pull it to zero, as the manual shows.
mount the ESC in the airflow behind a cooling inlet, not wrapped in foam.
turn the brake on for folding props so they fold when you glide.
What you need
Shop this list20 of 20 found in our store · ₹61,837
Hobbywing Skywalker 20A UBEC ESC: the part this guide coversHobbywing Skywalker 20A UBEC ESC₹1,199
Hobbywing Skywalker 30A UBEC ESC: another version this guide coversHobbywing Skywalker 30A UBEC ESC₹1,529
Hobbywing Skywalker 40A Brushless ESC: another version this guide coversHobbywing Skywalker 40A Brushless ESC₹1,439
Hobbywing Skywalker 50A UBEC Brushless ESC: another version this guide coversHobbywing Skywalker 50A UBEC Brushless ESC₹2,299
Hobbywing Skywalker-60A UBEC ESC 3-6S LiPo: another version this guide coversHobbywing Skywalker-60A UBEC ESC 3-6S LiPo₹2,849
Hobbywing Skywalker 80A UBEC Brushless ESC 3-6S: another version this guide coversHobbywing Skywalker 80A UBEC Brushless ESC 3-6S₹4,289
Hobbywing Skywalker 100A V2-UBEC ESC – 3-6S for RC Planes: another version this guide coversHobbywing Skywalker 100A V2-UBEC ESC – 3-6S for RC Planes₹3,999
Hobbywing SKYWALKER-30A-V2 30A Fixed Wing ESC 3-4S: another version this guide coversHobbywing SKYWALKER-30A-V2 30A Fixed Wing ESC 3-4S₹1,459
Hobbywing SKYWALKER-40A-V2 40A Fixed-Wing ESC: another version this guide coversHobbywing SKYWALKER-40A-V2 40A Fixed-Wing ESC₹1,809
Hobbywing SKYWALKER-50A-V2 50A Fixed Wing ESC: another version this guide coversHobbywing SKYWALKER-50A-V2 50A Fixed Wing ESC₹2,476
SURPASS 20A Brushless ESC 2-4S LiPo with 5.5V/4A BEC: another version this guide coversSURPASS 20A Brushless ESC 2-4S LiPo with 5.5V/4A BEC₹799
SURPASS 30A 2-4S SBEC 5.5V/4A ESC w/ 3.5mm Connector: another version this guide coversSURPASS 30A 2-4S SBEC 5.5V/4A ESC w/ 3.5mm Connector₹1,319
Surpass Hobby 40A ESC 2-4S LiPo/5-12NC NiMH 5V/6V BEC: another version this guide coversSurpass Hobby 40A ESC 2-4S LiPo/5-12NC NiMH 5V/6V BEC₹1,899
Surpass Hobby 50A ESC w/ 5V/6V 4A SBEC, 4.0mm Connector: another version this guide coversSurpass Hobby 50A ESC w/ 5V/6V 4A SBEC, 4.0mm Connector₹2,179
Surpass Hobby 60A SBEC ESC 2-6S LiPo w/ 4.0mm Connector: another version this guide coversSurpass Hobby 60A SBEC ESC 2-6S LiPo w/ 4.0mm Connector₹3,019
Surpass Hobby 80A 2-6S SBEC ESC w/ 4.0mm Connector: another version this guide coversSurpass Hobby 80A 2-6S SBEC ESC w/ 4.0mm Connector₹3,619
Surpass Hobby 100A 2-6S SBEC 5V/6V/8A ESC: another version this guide coversSurpass Hobby 100A 2-6S SBEC 5V/6V/8A ESC₹4,589
SunnySky X65A Pro SBEC 65A 3-6S Brushless ESC: another version this guide coversSunnySky X65A Pro SBEC 65A 3-6S Brushless ESC₹7,159
SunnySky X65A LW 3-6S 65A Brushless ESC: another version this guide coversSunnySky X65A LW 3-6S 65A Brushless ESC₹4,649
SunnySky X85A PRO SBEC 3-6S 85A ESC: another version this guide coversSunnySky X85A PRO SBEC 3-6S 85A ESC₹9,259
Alternatives and when to choose them
- Multirotor ESCs: no brake, faster response.
- High-current UBEC: more servo power.
- Heavy-lift ESCs: 12S and up.
Common mistakes to avoid
- Overloading a linear BEC with many or large servos.
- Mounting the ESC inside foam with no airflow.
- Skipping throttle calibration after changing radios.
- Running two BECs in parallel on the same servo rail.
Frequently asked questions
What does the BEC on an ESC do?
It is a regulator inside the ESC that turns battery voltage into 5 or 6 V for the receiver and servos.
How do I calibrate the throttle range?
Switch on the radio at full throttle, plug in the battery, wait for the beeps, then move throttle to zero.
How many servos can a linear BEC handle?
Usually two to four small servos on 2S or 3S; beyond that, use a switching BEC.
Why does the motor beep but not start?
Throttle is not at zero at power-up, or the radio throttle range has not been calibrated.
When should I turn the brake on?
Turn it on with folding props so they fold back cleanly while the plane glides.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.








