Component guide · Beginner · 4 min read
Learning Flight Controllers

KK2.1 and KK2.1.5 LCD, OpenPilot CC3D EVO, Naze32 6DOF, 10DOF and REV6, SP Racing F3, F3 EVO, Whoop Lite F3 and LiteWing ESP32 Drone Board
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These are older or simpler flight controllers used in classrooms and first builds. The KK2.1 has an LCD and buttons, so you can set it up without a computer. CC3D, Naze32 and SP Racing F3 boards run older Cleanflight or Betaflight versions. Brushed F3 boards fly tiny whoops, and the LiteWing ESP32 board is a programmable drone for learning control code.
Key specs at a glance
- Processors
- ATmega644 (KK2), STM32F1 (CC3D, Naze32), STM32F3 (F3 boards), ESP32 (LiteWing)
- Firmware
- KK2 firmware, LibrePilot, Cleanflight, Betaflight 3.x
- Set-up
- LCD menu (KK2) or PC configurator
- Brushed
- Whoop Lite F3, F3 EVO brushed
- Programming
- Arduino / ESP-IDF on LiteWing
- Uses
- Teaching, F450 learning builds, tiny whoops
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1KK2.1 Multi-rotor LCD Flight Control Board With 6050MPU And Atmel 644PA₹4,829
Option 2KK2.1.5 Multi-Rotor Flight Controller with LCD₹4,034
Option 3OpenPilot CC3D EVO Flight Controller Straight Pin₹1,699
Option 4OpenPilot CC3D EVO Flight Controller with Side Pins₹1,599
Option 5Naze32 6DOF Flight Control Board₹1,090
Option 6Naze32 10DOF Flight Control Board₹1,696
What the Legacy and learning flight controllers (F3, Naze32, CC3D, KK2, ESP32) is
Legacy and learning flight controllers such as the KK2.1.5, APM 2.8 and CC3D are older boards still used for teaching drone basics and simple builds.
Current Betaflight no longer supports F1 and F3 chips, so use the last versions that do (Betaflight 3.2 for F1, 4.0 for F3). They fly well but lack modern filters and features.
For a new FPV build choose an F4 or F7 board. Keep these for workshops, spares and learning how stabilisation works.
Legacy and learning flight controllers (F3, Naze32, CC3D, KK2, ESP32) pinout
The pins on the Legacy and learning flight controllers (F3, Naze32, CC3D, KK2, ESP32) and what each one does.
| Pin | Function |
|---|---|
| Receiver inputs | PWM, PPM or SBUS |
| Motor outputs | ESC signal and BEC power |
| USB / LCD | Configuration |
| Brushed motor pads | On brushed F3 boards |
- Receiver inputs
- PWM, PPM or SBUS
- Motor outputs
- ESC signal and BEC power
- USB / LCD
- Configuration
- Brushed motor pads
- On brushed F3 boards
Wiring the Legacy and learning flight controllers (F3, Naze32, CC3D, KK2, ESP32)
KK2 and CC3D boards take ESC BEC power on the output rail; only one ESC should supply it. Check motor order against the board's frame diagram.
| Legacy and learning flight controllers (F3, Naze32, CC3D, KK2, ESP32) pin | Connection | Note |
|---|---|---|
| Receiver | Input pins (PPM on one wire) | Use the supplied loom |
| ESCs | Motor outputs 1 to 4 | One BEC red wire only |
| Battery | Through the PDB | - |
- Receiver
- Connection:
- Input pins (PPM on one wire)
- Note:
- Use the supplied loom
- ESCs
- Connection:
- Motor outputs 1 to 4
- Note:
- One BEC red wire only
- Battery
- Connection:
- Through the PDB
- Note:
- -
Example code
Check the LiteWing pin map for the IMU address and motor pins. KK2 boards need no code: use the LCD menu to load the motor layout and run the ACC calibration.
#include <Wire.h>
void setup() {
Serial.begin(115200);
Wire.begin();
Wire.beginTransmission(0x68); // MPU6050 on the board
Wire.write(0x6B); Wire.write(0); // wake up
Wire.endTransmission();
}
void loop() {
Wire.beginTransmission(0x68);
Wire.write(0x3B);
Wire.endTransmission(false);
Wire.requestFrom(0x68, 6);
int16_t ax = Wire.read() << 8 | Wire.read();
int16_t ay = Wire.read() << 8 | Wire.read();
int16_t az = Wire.read() << 8 | Wire.read();
float roll = atan2(ay, az) * 57.3;
float pitch = atan2(-ax, sqrt((float)ay * ay + (float)az * az)) * 57.3;
Serial.printf("roll %.1f pitch %.1f\n", roll, pitch);
delay(50);
}Setup and tuning
set up with the onboard screen and buttons; no PC software needed.
flash the last supported ArduCopter (3.2.1) with Mission Planner.
flash with LibrePilot or old Betaflight versions.
calibrate accelerometer, radio and ESCs.
these boards lack modern features and support, so use current boards for serious work.
What you need
Shop this list18 of 18 found in our store · ₹36,260
KK2.1 Multi-rotor LCD Flight Control Board With 6050MPU And Atmel 644PA: the part this guide coversKK2.1 Multi-rotor LCD Flight Control Board With 6050MPU And Atmel 644PA₹4,829
KK2.1.5 Multi-Rotor Flight Controller with LCD: another version this guide coversKK2.1.5 Multi-Rotor Flight Controller with LCD₹4,034
OpenPilot CC3D EVO Flight Controller Straight Pin: another version this guide coversOpenPilot CC3D EVO Flight Controller Straight Pin₹1,699
OpenPilot CC3D EVO Flight Controller with Side Pins: another version this guide coversOpenPilot CC3D EVO Flight Controller with Side Pins₹1,599
Naze32 6DOF Flight Control Board: another version this guide coversNaze32 6DOF Flight Control Board₹1,090
Naze32 10DOF Flight Control Board: another version this guide coversNaze32 10DOF Flight Control Board₹1,696
Naze 32 Full REV6 Flight Controller with Compass & Barometer: another version this guide coversNaze 32 Full REV6 Flight Controller with Compass & Barometer₹1,749
Acro Naze 32 Brush Flight Controller: another version this guide coversAcro Naze 32 Brush Flight Controller₹1,469
SP Racing F3 Flight Controller ACRO Version: another version this guide coversSP Racing F3 Flight Controller ACRO Version₹2,498
SP Racing F3 Flight Controller Deluxe: another version this guide coversSP Racing F3 Flight Controller Deluxe₹2,642
SP Racing F3 Flight Controller Integrate OSD ACRO Version: another version this guide coversSP Racing F3 Flight Controller Integrate OSD ACRO Version₹2,642
F3 EVO V2.0 Flight Controller: another version this guide coversF3 EVO V2.0 Flight Controller₹1,686
SP Racing F3 EVO Brushed Flight Control Board for Micro FPV Frame: another version this guide coversSP Racing F3 EVO Brushed Flight Control Board for Micro FPV Frame₹1,090
Whoop Lite F3 Mini Brushed Flight Controller: another version this guide coversWhoop Lite F3 Mini Brushed Flight Controller₹879
LiteWing ESP32 Programmable Drone Development Board: another version this guide coversLiteWing ESP32 Programmable Drone Development Board₹3,709
ELRS 2.4G receiver (PWM/CRSF): the radio control linkHGLRC ELRS 2.4G Receiver₹1,581Closest match, check the specs
iFlight XT30/XT60 smart smoke stopper: protects a new build on first power-upiFlight XT30/XT60 Smart Smoke Stopper 2-6S LiPo₹979Closest match, check the specs
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Alternatives and when to choose them
- F4 flight controllers: modern Betaflight.
- Pixhawk 2.4.8: GPS missions for learning.
- MPU6050: the IMU in many of these boards.
Common mistakes to avoid
- Expecting modern firmware on old boards.
- Using the APM internal compass.
- Skipping ESC calibration.
- Flying without failsafe.
Frequently asked questions
Is the APM 2.8 still supported?
No. The last ArduCopter version for it is 3.2.1.
Is the KK2.1.5 good for learning?
Yes, it shows PID and mixing on its screen.
Can I run Betaflight on CC3D?
Only old versions; current Betaflight dropped it.
Why does my APM compass not work?
Disable the internal compass and use an external GPS compass.
Should I buy these for a new drone?
For learning only; modern boards are better and supported.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

