Component guide · Beginner · 6 min read
Thin-Film Force Sensors

RP-C Round (C5 to C30), RP-S Square, RP-L Long Strip, RP-4D, POT-C36H12 and POT-W10L333, RFP602 1kg to 5kg, FSR402, Round and Square FSR Pads and RFP Voltage Module
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Thin-film force sensors are flat pads whose resistance falls from megaohms to a few kilohms as you press. The code tells you the shape: RP-C is round (C5 is 5mm, C30 is 30mm), RP-S is square, RP-L is a long strip and RP-4D senses four directions. Wire one in a divider with a 10k resistor to an analog pin, or use the RFP module for a ready voltage or digital output.
Key specs at a glance
- Range
- 0.5g-500g (RP-C5ST-0.1G) up to 20g-20kg (RP-C30, RP-S40)
- Thickness
- 0.3 to 0.4 mm
- Resistance
- Over 1 Mohm unloaded, down to a few kohm
- Response
- Under 1 ms
- LT / ST
- Long tail or short tail lead
- RFP module
- Converts resistance to 0-3.3/5V analog plus a comparator DO
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Force Sensitive Resistor RP-C10-LT (20g-3kg)₹269
Option 2Force Sensitive Resistor RP-C18.3-ST (20g-6kg) – Thin-Film Flexible Sensor₹176
Option 3Force Sensitive Resistor RP-C30-ST (20g-20kg)₹269
Option 4Force Sensitive Resistor RP-C5-LT (20g-1kg) – Thin Film Sensor₹188
Option 5Force Sensitive Resistor RP-C5ST-0.1G (0.5g-500g)₹339
Option 6Force Sensitive Resistor RP-C7.6-LT (30g-1.5kg) – Thin Film Sensor₹198
What the RP, RFP602 and POT thin-film force sensitive resistors is
RP and RFP thin-film force sensors are flexible force-sensing resistors (FSRs) whose resistance falls as you press, used for touch pads, grip sensing and simple weighing.
Use them for touch and squeeze detection, seat or bed presence, smart insoles, gripper contact and drum pads. Choose the sensing area to match the part that presses on it, and the range so the normal press sits in the middle.
Press through a small rubber or plastic puck the size of the active area; force spread past the edge is lost. Do not bend the film across the sensing area, and do not solder directly to the silver tabs: use the supplied connector or a crimp clincher.
RP, RFP602 and POT thin-film force sensitive resistors pinout
The pins on the RP, RFP602 and POT thin-film force sensitive resistors and what each one does.
| Pin | Function |
|---|---|
| Lead 1 | To 5V (no polarity) |
| Lead 2 | To the analog pin and the fixed resistor |
| Fixed resistor | 10k to GND (3.3k for heavy loads, 47k for light touch) |
| Tail | Do not bend at the sensing area |
| Connector | Bare pins, female housing or crimp on most |
- Lead 1
- To 5V (no polarity)
- Lead 2
- To the analog pin and the fixed resistor
- Fixed resistor
- 10k to GND (3.3k for heavy loads, 47k for light touch)
- Tail
- Do not bend at the sensing area
- Connector
- Bare pins, female housing or crimp on most
Wiring the RP, RFP602 and POT thin-film force sensitive resistors
Smaller fixed resistors spread the reading for heavy presses; larger ones make light touches easier to see.
| RP, RFP602 and POT thin-film force sensitive resistors pin | Connection | Note |
|---|---|---|
| FSR lead 1 | 5V | Or 3.3V |
| FSR lead 2 | A0 | Divider middle |
| 10k resistor | A0 to GND | Pull-down |
- FSR lead 1
- Connection:
- 5V
- Note:
- Or 3.3V
- FSR lead 2
- Connection:
- A0
- Note:
- Divider middle
- 10k resistor
- Connection:
- A0 to GND
- Note:
- Pull-down
Example code
FSRs are not precise scales. Calibrate the level against a few known weights and expect about 10% repeatability.
const int FSR = A0;
const float R_FIXED = 10000.0; // pull-down resistor
void setup() { Serial.begin(9600); }
void loop() {
int raw = analogRead(FSR);
if (raw < 10) { Serial.println("No press"); delay(200); return; }
float v = raw * 5.0 / 1023.0;
float rFsr = R_FIXED * (5.0 - v) / v; // FSR resistance in ohms
float g = 1.0 / rFsr; // conductance rises roughly with force
Serial.print("R = "); Serial.print(rFsr, 0);
Serial.print(" ohm, level = "); Serial.println(g * 1e6, 1);
delay(200);
}Setup and tuning
wire the sensor in series with a fixed resistor (often 10 kΩ) and read the middle point on an analog pin.
pick the model's force range (such as 20 g to 2 kg or up to 10 kg) for your use.
press only on the round sensing area; use a puck or rubber pad to spread force evenly.
do not bend or solder near the tail; use the supplied connector or crimp clips.
FSRs are for detecting and comparing force, not precise weighing.
What you need
Shop this list20 of 20 found in our store · ₹7,262
Force Sensitive Resistor RP-C10-LT (20g-3kg): the part this guide coversForce Sensitive Resistor RP-C10-LT (20g-3kg)₹269
Generic Force Sensitive Resistor RP-C18.3-ST (20g-6kg) – Thin-Film Flexible Sensor: another version this guide coversForce Sensitive Resistor RP-C18.3-ST (20g-6kg) – Thin-Film Flexible Sensor₹176
Generic Force Sensitive Resistor RP-C30-ST (20g-20kg): another version this guide coversForce Sensitive Resistor RP-C30-ST (20g-20kg)₹269
Generic Force Sensitive Resistor RP-C5-LT (20g-1kg) – Thin Film Sensor: another version this guide coversForce Sensitive Resistor RP-C5-LT (20g-1kg) – Thin Film Sensor₹188
Force Sensitive Resistor RP-C5ST-0.1G (0.5g-500g): another version this guide coversForce Sensitive Resistor RP-C5ST-0.1G (0.5g-500g)₹339
Generic Force Sensitive Resistor RP-C7.6-LT (30g-1.5kg) – Thin Film Sensor: another version this guide coversForce Sensitive Resistor RP-C7.6-LT (30g-1.5kg) – Thin Film Sensor₹198
Force Sensitive Resistor RP-C7.6-ST (30g-1.5kg) – Thin Film Sensor: another version this guide coversForce Sensitive Resistor RP-C7.6-ST (30g-1.5kg) – Thin Film Sensor₹167
Force Sensitive Resistor RP-C7.6ST-LF2 (2g-1.5kg) – 0.3mm Thin Film: another version this guide coversForce Sensitive Resistor RP-C7.6ST-LF2 (2g-1.5kg) – 0.3mm Thin Film₹166
Force Sensitive Resistor RP-L-600 (20g-10kg) – Flexible Pressure Sensor: another version this guide coversForce Sensitive Resistor RP-L-600 (20g-10kg) – Flexible Pressure Sensor₹849
Force Sensitive Resistor RP-S40-LT (10g-20kg): another version this guide coversForce Sensitive Resistor RP-S40-LT (10g-20kg)₹429
Force Sensitive Resistor RP-S40-ST (10g-20kg): another version this guide coversForce Sensitive Resistor RP-S40-ST (10g-20kg)₹799
Generic Force Sensitive Resistor RP-S5-ST (10g-1kg) – Thin Film Sensor: another version this guide coversForce Sensitive Resistor RP-S5-ST (10g-1kg) – Thin Film Sensor₹144
RP-4D Force Sensitive Resistor (10g-1kg) – 4-Direction Sensing, 0.3mm Film: another version this guide coversRP-4D Force Sensitive Resistor (10g-1kg) – 4-Direction Sensing, 0.3mm Film₹219
Generic RP-C10-ST Force Sensitive Resistor (20g-2kg) – 0.4mm Thickness: another version this guide coversRP-C10-ST Force Sensitive Resistor (20g-2kg) – 0.4mm Thickness₹279
RP-C18.3-LT Force Sensitive Resistor (20g-6kg) – Flexible Thin-Film Sensor: another version this guide coversRP-C18.3-LT Force Sensitive Resistor (20g-6kg) – Flexible Thin-Film Sensor₹186
RP-L-110 Force Sensitive Resistor (20g-10kg) – 0.4mm Thickness: another version this guide coversRP-L-110 Force Sensitive Resistor (20g-10kg) – 0.4mm Thickness₹349
Generic RP-L-130 Force Sensitive Resistor (20g-10kg): another version this guide coversRP-L-130 Force Sensitive Resistor (20g-10kg)₹669
Generic RP-L-400 Force Sensitive Resistor (20g-10kg) – Thin Film Pressure Sensor: another version this guide coversRP-L-400 Force Sensitive Resistor (20g-10kg) – Thin Film Pressure Sensor₹479
Generic POT-C36H12 Force Sensitive Resistor (20g-200g) – Thin Film Sensor: another version this guide coversPOT-C36H12 Force Sensitive Resistor (20g-200g) – Thin Film Sensor₹299
Generic POT-W10L333 Force Sensitive Resistor (20g-200g) – 33mm Long, 10mm Sensing Area: another version this guide coversPOT-W10L333 Force Sensitive Resistor (20g-200g) – 33mm Long, 10mm Sensing Area₹789
Alternatives and when to choose them
- Force sensitive resistor guide: FSR basics.
- SOUSHINE FSR400 series: FSR400 to FSR412 sizes.
- Bar load cells: for real weighing.
Common mistakes to avoid
- Soldering directly onto the tail.
- Pressing outside the sensing area.
- Using an FSR as a precision scale.
- Bending the tail sharply.
Frequently asked questions
How do I read a thin-film force sensor with Arduino?
Put it in a divider with a 10 kΩ resistor and read the voltage with analogRead.
Can it measure weight accurately?
No. FSRs drift and vary by about ±10 %; use a load cell for real weighing.
Why does the reading change while I keep pressing?
FSRs creep under constant force, which is normal for this type of sensor.
Can I solder wires to the tail?
Avoid it, because heat melts the film; use the supplied connector or crimp clips.
Which resistor should I use in the divider?
Start with 10 kΩ; use a larger value for light touches and smaller for heavy loads.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.












