Component guide · Intermediate · 4 min read
Tekscan FlexiForce Force Sensors

A101 Miniature, A201 1lb, 25lb and 100lb, A301 1lb, 25lb and 100lb, A401 25.4mm, A502 Ultra Thin Square and HT201 High Temperature
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
FlexiForce sensors are thin piezoresistive force sensors from Tekscan with better linearity and repeatability than ordinary FSRs. A201 is the 9.5mm general one in 1, 25 and 100lb ranges, A301 is a compact 2-pin version, A401 has a 25.4mm area, A502 is a large ultra-thin square, A101 is tiny and HT201 handles high temperatures. Drive them with an inverting op-amp for a linear output.
Key specs at a glance
- Ranges
- A201/A301: 0-4.4N (1lb), 0-111N (25lb), 0-445N (100lb); A401 111N; A502 222N
- Sensing area
- 3.8mm (A101), 9.5mm (A201, A301), 25.4mm (A401), 50.8mm square (A502)
- Linearity
- About ±3%
- Repeatability
- About ±2.5%
- Thickness
- About 0.2mm
- Connectors
- 2 or 3 male square pins (middle pin unused on 3-pin)
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Tekscan FlexiForce A101 Force Sensor – 2-Pin Male Square Pin₹1,129
Option 2Tekscan FlexiForce A201-100 Force Sensor – 0-100 lb Range, 3-Pin Square Connector₹2,069
Option 3Tekscan FlexiForce A201-25 Force Sensor – 111 N (11kg) Range, 3-Pin Male Square Pin₹1,939
Option 4Tekscan FlexiForce A201/1 Flex Sensor – 0-4.4N Force Range, 3-Pin Connector₹2,429
Option 5Tekscan FlexiForce A301-100 Force Sensor – 0-100 lb Range, 2-Pin Male Square Pin₹1,859
Option 6Tekscan FlexiForce A301-25 Force Sensor – 0-25 lb Range, 2-Pin Connector₹1,649
What the Tekscan FlexiForce A101, A201, A301, A401, A502 and HT201 force sensors is
Tekscan FlexiForce sensors are thin, flexible force sensors with good linearity, used in medical devices, robot grippers and product testing.
Use FlexiForce where you need a number you can trust: grip and pinch force, prosthetics and gait studies, clamping force and contact on robot fingers. The force must land on the whole sensing area through a puck; Tekscan sells and recommends one, and a 3D-printed disc works.
For the best linearity, use Tekscan's suggested circuit: drive the sensor with -0.5V to -1V and an inverting op-amp, so output voltage rises in a straight line with force. A plain 10k divider also works but is less linear. Condition a new sensor by loading it to about 110% a few times before calibrating.
Tekscan FlexiForce A101, A201, A301, A401, A502 and HT201 force sensors pinout
The pins on the Tekscan FlexiForce A101, A201, A301, A401, A502 and HT201 force sensors and what each one does.
| Pin | Function |
|---|---|
| Pin 1 | Sensor lead |
| Pin 2 | Not connected on 3-pin A201 |
| Pin 3 | Sensor lead |
| Puck | Spreads load over the active area |
| Feedback resistor | Sets sensitivity in the op-amp circuit |
- Pin 1
- Sensor lead
- Pin 2
- Not connected on 3-pin A201
- Pin 3
- Sensor lead
- Puck
- Spreads load over the active area
- Feedback resistor
- Sets sensitivity in the op-amp circuit
Wiring the Tekscan FlexiForce A101, A201, A301, A401, A502 and HT201 force sensors
Leave the middle pin of 3-pin A201 sensors unconnected.
| Tekscan FlexiForce A101, A201, A301, A401, A502 and HT201 force sensors pin | Connection | Note |
|---|---|---|
| Sensor lead | 5V | Simple divider |
| Other lead | A0 | Divider middle |
| 47k resistor | A0 to GND | Choose for your range |
| Op-amp option | MCP6004 inverting | For linear output |
- Sensor lead
- Connection:
- 5V
- Note:
- Simple divider
- Other lead
- Connection:
- A0
- Note:
- Divider middle
- 47k resistor
- Connection:
- A0 to GND
- Note:
- Choose for your range
- Op-amp option
- Connection:
- MCP6004 inverting
- Note:
- For linear output
Example code
Conditioning, then a three-point calibration with known weights, gives far better results than the raw divider maths.
const int FSR = A0;
const float R_FIXED = 10000.0; // pull-down resistor
void setup() { Serial.begin(9600); }
void loop() {
int raw = analogRead(FSR);
if (raw < 10) { Serial.println("No press"); delay(200); return; }
float v = raw * 5.0 / 1023.0;
float rFsr = R_FIXED * (5.0 - v) / v; // FSR resistance in ohms
float g = 1.0 / rFsr; // conductance rises roughly with force
Serial.print("R = "); Serial.print(rFsr, 0);
Serial.print(" ohm, level = "); Serial.println(g * 1e6, 1);
delay(200);
}Setup and tuning
use the recommended op-amp inverting circuit for linear output.
apply force across the full sensing area with a puck.
pre-load the sensor several times before calibrating.
calibrate with known loads near your range.
use the crimp connector; do not solder.
What you need
Shop this list13 of 14 found in our store · ₹24,494
Tekscan FlexiForce A101 Force Sensor – 2-Pin Male Square Pin: the part this guide coversTekscan FlexiForce A101 Force Sensor – 2-Pin Male Square Pin₹1,129
Tekscan FlexiForce A201-100 Force Sensor – 0-100 lb Range, 3-Pin Square Connector: another version this guide coversTekscan FlexiForce A201-100 Force Sensor – 0-100 lb Range, 3-Pin Square Connector₹2,069
Tekscan FlexiForce A201-25 Force Sensor – 111 N (11kg) Range, 3-Pin Male Square Pin: another version this guide coversTekscan FlexiForce A201-25 Force Sensor – 111 N (11kg) Range, 3-Pin Male Square Pin₹1,939
Tekscan FlexiForce A201/1 Flex Sensor – 0-4.4N Force Range, 3-Pin Connector: another version this guide coversTekscan FlexiForce A201/1 Flex Sensor – 0-4.4N Force Range, 3-Pin Connector₹2,429
Tekscan FlexiForce A301-100 Force Sensor – 0-100 lb Range, 2-Pin Male Square Pin: another version this guide coversTekscan FlexiForce A301-100 Force Sensor – 0-100 lb Range, 2-Pin Male Square Pin₹1,859
Tekscan FlexiForce A301-25 Force Sensor – 0-25 lb Range, 2-Pin Connector: another version this guide coversTekscan FlexiForce A301-25 Force Sensor – 0-25 lb Range, 2-Pin Connector₹1,649
Tekscan FlexiForce A301/1 Force Sensor – 0-111N Range, 2-Pin Connector: another version this guide coversTekscan FlexiForce A301/1 Force Sensor – 0-111N Range, 2-Pin Connector₹1,119
Tekscan FlexiForce A401 Force Sensor – 0-111 N (25 lb) Range, 25.4 mm Sensing Area: another version this guide coversTekscan FlexiForce A401 Force Sensor – 0-111 N (25 lb) Range, 25.4 mm Sensing Area₹2,769
Tekscan FlexiForce A502 Ultra Thin Force Sensor – 0-222 N Range, 2-Pin Male Square Pin Connector: another version this guide coversTekscan FlexiForce A502 Ultra Thin Force Sensor – 0-222 N Range, 2-Pin Male Square Pin Connector₹3,219
Tekscan FlexiForce HT201 High-Temperature Force Sensor – 3-Pin Square Pin Connector: another version this guide coversTekscan FlexiForce HT201 High-Temperature Force Sensor – 3-Pin Square Pin Connector₹6,019- Uno R3 development board: the controller used in the wiring tableFind this part
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Solderless breadboard: to build without solderingSolderless Breadboard₹68
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- SOUSHINE FSR400 series: low cost FSRs.
- TE compression load cells: rigid force cells.
- RP and RFP602 thin-film sensors: more shapes.
Common mistakes to avoid
- Skipping conditioning.
- Soldering the tail.
- Uneven loading.
- Using a simple divider when linearity matters.
Frequently asked questions
How is FlexiForce better than cheap FSRs?
It has better linearity and repeatability than low-cost FSRs.
Which circuit should I use?
Use the inverting op-amp circuit from Tekscan's datasheet for linear output.
Why do readings drift under constant load?
That is creep; calibrate with the same loading time as your real use.
Can I cut the sensor?
No. Cutting the sensor breaks its traces.
Can I use it with Arduino?
Yes, through the op-amp circuit or a simple divider on an analog pin.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

