Component guide · Intermediate · 3 min read
XH-M601 12V Battery Charging Control Board and HW-749 Li-ion Charge Controller

By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The XH-M601 and HW-749 boards sit between a charger and a battery and switch charging off with a relay when the battery reaches a set voltage, then on again when it drops. The XH-M601 suits 12 V lead-acid batteries with an existing charger; the HW-749 accepts 6 to 60 V and is set for Li-ion packs. They add automatic cut-off to simple chargers.
Key specs at a glance
- Voltage
- XH-M601 12 V; HW-749 6 to 60 V
- Switch
- Relay, about 10 A
- Settings
- Full voltage and restart voltage
- Display
- HW-749 shows voltage
- Current limit
- None; the charger sets current
- Use
- Charger cut-off and float control
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1XH-M601 12V Battery Charging Control Board₹122
Option 2Li-ion Charge Controller Module₹287
What the XH-M601 battery charge controller is
The XH-M601 is a battery charge controller module that switches a charger on and off by battery voltage, protecting 12 to 24 V lead-acid or lithium batteries from overcharge.
The board does not limit current. The charger or supply must have its own current limit, or the battery will draw too much when empty.
XH-M601 battery charge controller pinout
The pins on the XH-M601 battery charge controller and what each one does.
| Pin | Function |
|---|---|
| Charger IN | From charger or supply |
| BAT | To battery |
| Relay | Switches charger output |
- Charger IN
- From charger or supply
- BAT
- To battery
- Relay
- Switches charger output
Wiring the XH-M601 battery charge controller
Connect the XH-M601 battery charge controller like this.
| XH-M601 battery charge controller pin | XH-M601 | HW-749 |
|---|---|---|
| Charger IN | 12 V lead-acid charger | Current-limited supply |
| BAT | 12 V battery | Li-ion pack with BMS |
- Charger IN
- XH-M601:
- 12 V lead-acid charger
- HW-749:
- Current-limited supply
- BAT
- XH-M601:
- 12 V battery
- HW-749:
- Li-ion pack with BMS
Example code
A minimal sketch to check the part works.
1. Connect the battery first, then the input source.
2. Measure charge voltage at the battery terminals.
3. Watch cell temperature during the first full charge.Setup and tuning
connect battery and charger as the diagram shows; the relay switches the charger.
set the start-charging and stop-charging voltages.
set voltages for your chemistry (lead-acid, LiFePO4).
stay within the relay rating.
switching mains needs a safe enclosure and qualified wiring.
What you need
Shop this list4 of 4 found in our store · ₹884
XH-M601 12V Battery Charging Control Board: the part this guide coversXH-M601 12V Battery Charging Control Board₹122
Li-ion Charge Controller Module: another version this guide coversLi-ion Charge Controller Module₹287
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
SMPS power supply in metal enclosure (5/12/24 V): a 12 or 24 V charging sourceSMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
Alternatives and when to choose them
- 300W CC/CV buck: adds current limit.
- PWM solar charge controller.
- AA, NiMH and lead-acid batteries.
Common mistakes to avoid
- Wrong voltage set points.
- Overloading the relay.
- Unsafe mains wiring.
- Narrow voltage gap.
Frequently asked questions
How does the XH-M601 protect batteries?
It turns off the charger at the stop voltage and on at the start voltage.
What voltages should I set for 12 V lead-acid?
Typically start around 12.0 to 12.5 V and stop at about 13.8 to 14.4 V.
Can it be used for lithium batteries?
Yes, as long as the start and stop voltages are set for that chemistry.
Can the relay switch mains chargers?
Only within its rating, inside a safe enclosure wired by a qualified person.
Why does the relay click often?
The start and stop voltages are too close together; widen the gap.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
