Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsThe TSOP IR receiver turns a remote button into a code, and the Uno toggles one of two relay channels for each button. Great for learning how remotes talk to devices.
Keep the loads low voltage; mains wiring is for electricians.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
38 kHz infrared receiver that decodes button codes from almost any TV or AC remote.
Two isolated relays on one board, each switched by its own pin.
Follow the colours: red is power, dark grey is ground, blue is a signal.
atl_ir_remote_two_lamps.inoVerify & upload in Electrolark// IR remote two-lamp switch
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "atl-ir-remote-two-lamps"
#include <IRremote.hpp>
// ---- pins ----
const uint8_t IR_PIN = 2;
const uint8_t RELAY_1 = 3;
const uint8_t RELAY_2 = 4;
// Press remote buttons with the Serial Monitor open, then put their command numbers here
const uint16_t CMD_CH1 = 0x0C; // button "1" on many NEC remotes
const uint16_t CMD_CH2 = 0x18; // button "2"
const uint16_t CMD_ALL_OFF = 0x45;
bool ch1 = false, ch2 = false;
void applyRelays() {
digitalWrite(RELAY_1, ch1 ? LOW : HIGH); // active-LOW relay board
digitalWrite(RELAY_2, ch2 ? LOW : HIGH);
}
void setup() {
Serial.begin(115200);
IrReceiver.begin(IR_PIN);
pinMode(RELAY_1, OUTPUT);
pinMode(RELAY_2, OUTPUT);
applyRelays();
}
void loop() {
if (!IrReceiver.decode()) return;
uint16_t cmd = IrReceiver.decodedIRData.command;
bool repeat = IrReceiver.decodedIRData.flags & IRDATA_FLAGS_IS_REPEAT;
IrReceiver.resume();
if (repeat) return; // ignore held-button repeats
Serial.print(F("IR command 0x")); Serial.println(cmd, HEX);
if (cmd == CMD_CH1) ch1 = !ch1;
else if (cmd == CMD_CH2) ch2 = !ch2;
else if (cmd == CMD_ALL_OFF) ch1 = ch2 = false;
applyRelays();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Point the remote straight at the receiver, check the OUT pin, and try a fresh remote battery.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Digital 38kHz Infrared Receiver Module, 5V Relay Module with Optocoupler (2 channel), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 7 steps.
No. This page has the complete, tested code (atl_ir_remote_two_lamps.ino). Install this library first: IRremote.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹437 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Infrared remote protocols (NEC); Isolation, relays and switching higher-power loads.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.