LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe relay switches a 12 V lamp or LED strip whenever the PIR sees movement and keeps it on for 15 seconds after the last motion. A first step to automatic corridor and cupboard lights.
Keep this to low-voltage lamps. Mains wiring must be done by an electrician.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Passive infrared sensor that detects the body heat of moving people or animals up to about 7 m away.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Follow the colours: red is power, dark grey is ground, blue is a signal.
atl_motion_lamp.inoVerify & upload in Electrolark// Motion-activated lamp
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "atl-motion-lamp"
// ---- pins ----
const uint8_t PIR_PIN = 2;
const uint8_t RELAY_PIN = 3;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
bool motion = false;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const unsigned long HOLD_MS = 15000; // stay on this long after the last trigger
unsigned long lastTrigger = 0;
const unsigned long WARMUP_MS = 30000UL; // sensor warm-up
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void evaluate() {
if (millis() < WARMUP_MS) { alertOn = false; statusText = "Warming up"; return; }
if (motion) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "Light on" : "Waiting";
}
void setup() {
Serial.begin(115200);
pinMode(PIR_PIN, INPUT);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
motion = digitalRead(PIR_PIN) == HIGH;
evaluate();
Serial.print(F("Motion="));
Serial.print(motion ? F("yes") : F("no"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setRelay(alertOn);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Give it a minute to settle after power-up and keep it away from heaters, windows and fans.
Turn the sensitivity (Sx) pot clockwise and check the module has 5 V on VCC.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, HC-SR501 PIR Motion Detector Sensor Module, 5V Relay Module with Optocoupler (1 channel), Through-Hole LED Pack (Pack of 10), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 7 steps.
No. This page has the complete, tested code (atl_motion_lamp.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹473 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Digital inputs and sensor hold time; Isolation, relays and switching higher-power loads.
Ideas that reuse this build: PIR intruder alarm. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Motion=no, status=Warming up Motion=no, status=Warming up
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.