Double-clap light switch
Clap twice and the lights come on. Clap twice again to switch them off.
Shop by category
Shop all componentsRecord "Welcome to our tinkering lab" on the ISD1820, then let the PIR do the rest. When someone walks up, the Uno pulses the PLAYE pin and the voice module speaks. It waits 15 seconds before it greets again.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Passive infrared sensor that detects the body heat of moving people or animals up to about 7 m away.
Records a short message (about 10 seconds) and plays it back through its speaker when the PLAYE pin gets a pulse.
Follow the colours: red is power, dark grey is ground, blue is a signal.
atl_talking_welcome_board.inoVerify & upload in Electrolark// Talking welcome board
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "atl-talking-welcome-board"
// ---- pins ----
const uint8_t PIR_PIN = 2;
const uint8_t VOICE_PLAY = 3;
const uint8_t VOICE_REC = 4;
// ---- latest readings ----
bool motion = false;
const unsigned long QUIET_MS = 15000; // wait this long before greeting again
unsigned long lastGreet = 0;
void playVoice(bool on) {
static bool wasOn = false;
if (on && !wasOn) { // pulse PLAYE once per trigger
digitalWrite(VOICE_PLAY, HIGH);
delay(60);
digitalWrite(VOICE_PLAY, LOW);
}
wasOn = on;
}
void setup() {
Serial.begin(115200);
pinMode(PIR_PIN, INPUT);
pinMode(VOICE_PLAY, OUTPUT); pinMode(VOICE_REC, OUTPUT);
digitalWrite(VOICE_PLAY, LOW); digitalWrite(VOICE_REC, LOW);
}
void loop() {
if (digitalRead(PIR_PIN) == HIGH && (lastGreet == 0 || millis() - lastGreet > QUIET_MS)) {
Serial.println(F("Visitor: playing message"));
playVoice(true);
delay(100);
playVoice(false);
lastGreet = millis();
}
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Give it a minute to settle after power-up and keep it away from heaters, windows and fans.
Turn the sensitivity (Sx) pot clockwise and check the module has 5 V on VCC.
Record a message first (hold REC), check the speaker is on SP+ and SP-, and make sure PLAYE is wired to the right pin.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, HC-SR501 PIR Motion Detector Sensor Module, ISD1820 Voice Recorder and Playback Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (atl_talking_welcome_board.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹516 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Digital inputs and sensor hold time; Digital sound recording and playback.
Clap twice and the lights come on. Clap twice again to switch them off.
Plays a friendly ding-dong whenever someone walks into the shop or room.
Beeps and flashes any message in Morse, or key your own by hand.
Turn a membrane keypad into a two-octave piano.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.