LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA magnet on a wheel passes the Hall sensor once per turn. Multiply the turns by the wheel's circumference and you have the distance; the sketch then applies a minimum fare for the first 1.5 km and a rate per km after that. Try it on a bicycle wheel to learn how real meters work, then change the fares to your city's rates.
A learning model. Fare meters used in vehicles must be government-approved and sealed.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
auto_rickshaw_fare_meter_model.inoVerify & upload in Electrolark// Auto-rickshaw fare meter model
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "auto-rickshaw-fare-meter-model"
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t HALL_PIN = 2;
const uint8_t BUTTON_PIN = 3;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
bool magnet = false;
const float WHEEL_M = 1.30; // distance per wheel turn in metres: measure your wheel
const float BASE_KM = 1.5; // minimum fare covers this distance
const float BASE_FARE = 30; // rupees
const float PER_KM = 15; // rupees per km after that
unsigned long pulses = 0;
bool lastMagnet = false, running = false;
unsigned long lastShow = 0;
float tripKm() { return pulses * WHEEL_M / 1000.0f; }
float fareNow() { float km = tripKm(); return BASE_FARE + (km > BASE_KM ? (km - BASE_KM) * PER_KM : 0); }
void setup() {
Serial.begin(115200);
pinMode(HALL_PIN, INPUT);
lcd.init();
lcd.backlight();
pinMode(BUTTON_PIN, INPUT_PULLUP);
lcd.print(F("Press to start"));
}
void loop() {
magnet = digitalRead(HALL_PIN) == LOW;
if (running && magnet && !lastMagnet) pulses++; // count each pass of the magnet
lastMagnet = magnet;
if (digitalRead(BUTTON_PIN) == LOW) {
unsigned long t = millis();
while (digitalRead(BUTTON_PIN) == LOW) delay(10);
if (millis() - t > 2000) { running = false; pulses = 0; lcd.clear(); lcd.print(F("Press to start")); } // hold 2 s: clear
else { running = !running; Serial.println(running ? F("Trip started") : F("Trip stopped")); }
}
if (millis() - lastShow < 500 || (!running && pulses == 0)) return;
lastShow = millis();
lcd.setCursor(0, 0); lcd.print(tripKm(), 2); lcd.print(F(" km ")); lcd.print(running ? F("RUN ") : F("STOP"));
lcd.setCursor(0, 1); lcd.print(F("Fare Rs ")); lcd.print(fareNow(), 0); lcd.print(F(" "));
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Flip the magnet and adjust the trimmer.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Linear Magnetic Hall Sensor Module – LM393, LCD1602 16x2 Character LCD (blue, with I2C adapter), Tactile Push Button Switch, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (auto_rickshaw_fare_meter_model.ino). Install this library first: LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹482 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Character displays and I²C backpacks; Magnetic sensing; Pull-ups and debouncing.
A learning model. Fare meters used in vehicles must be government-approved and sealed.
Ideas that reuse this build: Bike speedometer and Hamster wheel odometer. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.