Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsHamsters can run several kilometres a night. A small magnet on the wheel passes a reed switch once a turn; the Nano works out the speed and the total distance and shows them on the OLED. A great data project for children.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Glass switch whose contacts close when a magnet is near.
Follow the colours: red is power, dark grey is ground, blue is a signal.
hamster_wheel_odometer.inoVerify & upload in Electrolark// Hamster wheel odometer
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "hamster-wheel-odometer"
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t REED_PIN = 2;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
bool doorOpen = false;
const float WHEEL_M = 2.1; // wheel circumference in metres (26" wheel ≈ 2.1 m)
unsigned long revs = 0, lastRev = 0, lastShow = 0;
float kmh = 0;
bool wasClosed = false;
void show() {
oled.clearDisplay(); oled.setTextSize(1); oled.setCursor(0, 0); oled.print(F("km/h"));
oled.setTextSize(3); oled.setCursor(0, 12); oled.print(kmh, 1);
oled.setTextSize(1); oled.setCursor(0, 50); oled.print(F("Trip ")); oled.print(revs * WHEEL_M / 1000.0f, 2); oled.print(F(" km"));
oled.display();
}
void setup() {
Serial.begin(115200);
pinMode(REED_PIN, INPUT_PULLUP);
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
bool closed = digitalRead(REED_PIN) == LOW;
if (closed && !wasClosed) {
unsigned long now = millis();
if (now - lastRev > 60) { // ignore switch bounce
if (lastRev) kmh = WHEEL_M / ((now - lastRev) / 1000.0f) * 3.6f;
lastRev = now; revs++;
}
}
wasClosed = closed;
if (millis() - lastRev > 3000) kmh = 0; // stopped
if (millis() - lastShow > 250) { lastShow = millis(); show(); }
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Bring the magnet within 1 cm and align it parallel to the glass body.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), Y213 Reed Switch Normally Open (glass), 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (hamster_wheel_odometer.ino). Install these libraries first: Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹442 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Drawing text on an I²C display; Pull-up resistors and reed switches.
Ideas that reuse this build: Bike speedometer and Hall tachometer. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.