LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsSkin colour changes from green to yellow to brown as bananas ripen. The TCS3200 reads the red, green and blue levels, and simple rules turn them into a verdict on the LCD. Fruit sellers can sort stock, and students learn about colour classification.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
An 8×8 array of photodiodes with red, green, blue and clear filters.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
banana_ripeness_colour_checker.inoVerify & upload in Electrolark// Banana ripeness colour checker
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "banana-ripeness-colour-checker"
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t CS_S0 = 2;
const uint8_t CS_S1 = 3;
const uint8_t CS_S2 = 4;
const uint8_t CS_S3 = 5;
const uint8_t CS_OUT = 6;
LiquidCrystal_I2C lcd(0x27, 16, 2);
int R_MIN = 25, R_MAX = 160; // calibrate: pulse widths in microseconds for the brightest and darkest card
int G_MIN = 30, G_MAX = 180;
int B_MIN = 25, B_MAX = 150;
int readChannel(bool s2, bool s3, int lo, int hi) {
digitalWrite(CS_S2, s2 ? HIGH : LOW);
digitalWrite(CS_S3, s3 ? HIGH : LOW);
delay(5);
long us = pulseIn(CS_OUT, LOW, 20000UL);
return constrain(map(us, lo, hi, 255, 0), 0, 255); // shorter pulse = more of that colour
}
void setup() {
Serial.begin(115200);
pinMode(CS_S0, OUTPUT); pinMode(CS_S1, OUTPUT); pinMode(CS_S2, OUTPUT); pinMode(CS_S3, OUTPUT); pinMode(CS_OUT, INPUT);
digitalWrite(CS_S0, HIGH); digitalWrite(CS_S1, LOW); // 20 % output scaling
lcd.init();
lcd.backlight();
}
void loop() {
int r = readChannel(false, false, R_MIN, R_MAX);
int g = readChannel(true, true, G_MIN, G_MAX);
int bl = readChannel(false, true, B_MIN, B_MAX);
const char* verdict;
if (r + g + bl < 150) verdict = "Too dark: retry";
else if (g > r + 20) verdict = "Unripe (green)";
else if (r > 150 && g > 120 && bl < 90) verdict = "Ripe: eat now";
else if (r > g + 30 && g < 110) verdict = "Overripe: bake";
else verdict = "Almost ripe";
lcd.clear(); lcd.print(F("Banana colour")); lcd.setCursor(0, 1); lcd.print(verdict);
Serial.print(verdict); Serial.print(F(" R=")); Serial.print(r); Serial.print(F(" G=")); Serial.print(g); Serial.print(F(" B=")); Serial.println(bl);
delay(500);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Calibrate with white and black paper first and adjust the min/max values.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, TCS3200 Colour Recognition Sensor Module, LCD1602 16x2 Character LCD (blue, with I2C adapter), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (banana_ripeness_colour_checker.ino). Install this library first: LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,030 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Character displays and I²C backpacks; Colour filters and frequency output.
Ideas that reuse this build: Talking colour identifier and Colour detector light. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Too dark: retry R=0 G=0 B=0 Too dark: retry R=0 G=0 B=0 Too dark: retry R=0 G=0 B=0 Too dark: retry R=0 G=0 B=0 Too dark: retry R=0 G=0 B=0
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.