LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe TCS3200 measures how much red, green and blue light an object reflects. The Uno scales those to 0–255 and paints the LED ring the same colour: a simple first step towards colour-sorting machines.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
An 8×8 array of photodiodes with red, green, blue and clear filters.
Sixteen individually addressable RGB LEDs on one data wire.
Follow the colours: red is power, dark grey is ground, blue is a signal.
colour_detector_light.inoVerify & upload in Electrolark// Colour detector with RGB ring
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "colour-detector-light"
#include <Adafruit_NeoPixel.h>
// ---- pins ----
const uint8_t CS_S0 = 2;
const uint8_t CS_S1 = 3;
const uint8_t CS_S2 = 4;
const uint8_t CS_S3 = 5;
const uint8_t CS_OUT = 6;
const uint8_t RING_PIN = 7;
const int RING_LEDS = 16;
Adafruit_NeoPixel ring(RING_LEDS, RING_PIN, NEO_GRB + NEO_KHZ800);
// calibrate: read white and black paper and update these pulse widths (microseconds)
int R_MIN = 25, R_MAX = 160;
int G_MIN = 30, G_MAX = 180;
int B_MIN = 25, B_MAX = 150;
void showLevel(int pct, uint32_t color) {
int lit = constrain(pct, 0, 100) * RING_LEDS / 100;
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, i < lit ? color : 0);
ring.show();
}
int readChannel(bool s2, bool s3, int lo, int hi) {
digitalWrite(CS_S2, s2 ? HIGH : LOW);
digitalWrite(CS_S3, s3 ? HIGH : LOW);
delay(5);
long us = pulseIn(CS_OUT, LOW, 20000UL);
return constrain(map(us, lo, hi, 255, 0), 0, 255); // shorter pulse = more of that colour
}
void setup() {
Serial.begin(115200);
pinMode(CS_S0, OUTPUT); pinMode(CS_S1, OUTPUT); pinMode(CS_S2, OUTPUT); pinMode(CS_S3, OUTPUT); pinMode(CS_OUT, INPUT);
digitalWrite(CS_S0, HIGH); digitalWrite(CS_S1, LOW); // 20 % output scaling
ring.begin();
ring.setBrightness(40);
ring.show();
}
void loop() {
int r = readChannel(false, false, R_MIN, R_MAX);
int g = readChannel(true, true, G_MIN, G_MAX);
int bl = readChannel(false, true, B_MIN, B_MAX);
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, ring.Color(r, g, bl));
ring.show();
Serial.print(F("R=")); Serial.print(r); Serial.print(F(" G=")); Serial.print(g); Serial.print(F(" B=")); Serial.println(bl);
delay(150);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Calibrate with white and black paper first and adjust the min/max values.
Add the 330 Ω resistor in series with DIN and share GND with the board.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, TCS3200 Colour Recognition Sensor Module, WS2812 RGB LED Ring (16 LEDs), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (colour_detector_light.ino). Install this library first: Adafruit NeoPixel.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,003 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Addressable LEDs and colour mixing; Colour filters and frequency output.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
G=0 B=0 R=0 G=0 B=0 R=0 G=0 B=0 R=0 G=0 B=0 R=0 G=0 B=0 R=0 G=0 B=0 R=0 G=0 B=0
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.