LM317 variable power supply
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Shop by category
Shop all componentsA battery can show 12.6 V at rest and still fail to start the car. The real test is the voltage while the starter motor turns. Plug this into the car's 12 V socket or clip it to the battery, start the engine, and the OLED shows the lowest voltage it caught, with a verdict: above 10.5 V is strong, below 9.6 V needs a test at a battery shop.
Keep clear of the fan and belts. Clip on with the engine off.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Two resistors scale the battery voltage down by 11 so an analog pin can measure up to about 50 V safely.
Follow the colours: red is power, dark grey is ground, blue is a signal.
Power the Nano from a USB phone charger in the 12 V socket, not from the battery leads, so the board does not reset during cranking.
car_battery_cranking_tester.inoVerify & upload in Electrolark// Car battery cranking voltage tester
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "car-battery-cranking-tester"
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t VBAT_PIN = A0;
const uint8_t BUTTON_PIN = 2;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float batteryV = 0;
float lowest = 99, lastV = 0;
unsigned long lastShow = 0;
float readBatteryV() { return analogRead(VBAT_PIN) * VREF / ADC_MAX * 11.0f; } // 100 kΩ : 10 kΩ divider = ÷11
const char* verdict(float v) { // a healthy 12 V battery stays above about 9.6 V while cranking
if (v > 10.5) return "Strong";
if (v > 9.6) return "OK";
return "Weak: test it";
}
void setup() {
Serial.begin(115200);
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
pinMode(BUTTON_PIN, INPUT_PULLUP);
}
void loop() {
batteryV = readBatteryV();
if (batteryV > 3 && batteryV < lowest) lowest = batteryV; // fast sampling catches the dip while the starter turns
if (digitalRead(BUTTON_PIN) == LOW) { lowest = 99; delay(300); }
if (millis() - lastShow < 300) return;
lastShow = millis();
oled.clearDisplay(); oled.setTextSize(1); oled.setCursor(0, 0); oled.print(F("Battery now"));
oled.setTextSize(2); oled.setCursor(0, 10); oled.print(batteryV, 2); oled.print(F(" V"));
oled.setTextSize(1); oled.setCursor(0, 34); oled.print(F("Lowest while cranking"));
oled.setCursor(0, 44); if (lowest < 90) { oled.print(lowest, 2); oled.print(F(" V ")); oled.print(verdict(lowest)); } else oled.print(F("start the engine"));
oled.setCursor(0, 56); oled.print(F("Button: reset"));
oled.display();
Serial.print(batteryV, 2); Serial.print(F(" V, lowest ")); Serial.println(lowest, 2);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Measure the real resistor values and change 11.0 to (R1 + R2) / R2.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), Resistor Assortment Kit (30 Values), 0.96" OLED Display 128x64 (I2C), Tactile Push Button Switch, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (car_battery_cranking_tester.ino). Install these libraries first: Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹459 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Drawing text on an I²C display; Pull-ups and debouncing; Voltage dividers and ADC scaling.
Keep clear of the fan and belts. Clip on with the engine off.
Ideas that reuse this build: Alternator charging check and Battery voltage tester. They are listed under Take it further on this page.
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Build your own USB power bank and learn how lithium charging works.
Free power for outdoor sensors: sunlight in, 5 V USB out.
Beeps when the mains goes off at night, so the fridge and the alarm clock do not quietly die.
Learning project. Check every circuit and the datasheet of each part before you power it up.
16.56 V, lowest 16.45 16.45 V, lowest 16.45 16.51 V, lowest 16.45 16.51 V, lowest 16.45 16.56 V, lowest 16.45 16.51 V, lowest 16.45 16.51 V, lowest 16.45 16.51 V, lowest 16.45
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.