Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsPress to show the hours, minutes or seconds as a binary number; students decode it and race each other.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Three indicator LEDs, each through a 330 Ω resistor to its pin.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_binary_clock.inoVerify & upload in Electrolark// Binary clock
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-binary-clock"
#include <Wire.h>
#include <RTClib.h>
// ---- pins ----
const uint8_t LED_RED = 2;
const uint8_t LED_YELLOW = 3;
const uint8_t LED_GREEN = 4;
RTC_DS3231 rtc;
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setYellowLed(bool on) { digitalWrite(LED_YELLOW, on ? HIGH : LOW); }
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void setLed(int n, bool on) { if (n == 1) setRedLed(on); else if (n == 2) setYellowLed(on); else setGreenLed(on); }
void setup() {
Serial.begin(115200);
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
pinMode(LED_RED, OUTPUT); pinMode(LED_YELLOW, OUTPUT); pinMode(LED_GREEN, OUTPUT);
}
void loop() {
DateTime now = rtc.now();
int s = now.second() % 8; // seconds modulo 8 on three LEDs
digitalWrite(LED_RED, s & 1);
digitalWrite(LED_YELLOW, (s >> 1) & 1);
digitalWrite(LED_GREEN, (s >> 2) & 1);
Serial.print(now.hour()); Serial.print(':'); Serial.print(now.minute()); Serial.print(':'); Serial.print(now.second());
Serial.print(F(" seconds mod 8 = ")); Serial.println(s);
delay(250);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
It is backwards: the long leg goes to the resistor.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Make a decoding card for the wall.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, DS3231 Precision RTC Module with EEPROM, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 7 steps.
No. This page has the complete, tested code (class_binary_clock.ino). Install this library first: RTClib.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹495 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Binary; Time.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
30:1 seconds mod 8 = 1 9:30:1 seconds mod 8 = 1 9:30:1 seconds mod 8 = 1 9:30:2 seconds mod 8 = 2 9:30:2 seconds mod 8 = 2 9:30:2 seconds mod 8 = 2
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.