Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsEach spike above the threshold is one clap. Students compete to clap fastest, then discover the sensor misses claps if they come faster than about five a second.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Bright 4-digit 7-segment display driven by two wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_clap_counter.inoVerify & upload in Electrolark// Clap counter
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-clap-counter"
#include <TM1637Display.h>
// ---- pins ----
const uint8_t MIC_PIN = A0;
const uint8_t SEG_CLK = 2;
const uint8_t SEG_DIO = 3;
const uint8_t BUTTON_PIN = 4;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
int soundPct = 0;
const int CLAP_LEVEL = 40; // Sound % that counts as a clap
int claps = 0;
unsigned long lastClap = 0;
int readSoundLevel() {
// peak-to-peak amplitude over a 50 ms window
unsigned long start = millis();
int lo = ADC_MAX, hi = 0;
while (millis() - start < 50) {
int v = analogRead(MIC_PIN);
if (v < lo) lo = v;
if (v > hi) hi = v;
}
return (int)((hi - lo) * 100L / ADC_MAX);
}
void setup() {
Serial.begin(115200);
seg.setBrightness(5);
seg.clear();
pinMode(BUTTON_PIN, INPUT_PULLUP);
seg.showNumberDec(0);
}
void loop() {
int s = readSoundLevel();
if (s > CLAP_LEVEL && millis() - lastClap > 150) { // 150 ms gap stops one clap counting twice
claps++;
lastClap = millis();
seg.showNumberDec(claps);
Serial.println(claps);
}
if (digitalRead(BUTTON_PIN) == LOW) { claps = 0; seg.showNumberDec(0); delay(300); }
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Turn the module trimmer to increase gain, or move the mic closer to the sound.
CLK and DIO swapped; swap them.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Run a challenge: who can clap exactly 20 times in 10 seconds?
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Analog Sound Sensor Microphone Module, TM1637 4-Digit 7-Segment Display Module, Tactile Push Button Switch, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 8 steps.
No. This page has the complete, tested code (class_clap_counter.ino). Install this library first: TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹488 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Thresholds; Counting events.
Ideas that reuse this build: Clap switch. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.