LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA small magnet on the bob passes the Hall sensor at the lowest point of every swing, twice per full cycle. The sketch times two passes and doubles the interval to show the period in milliseconds on the display; the Serial Monitor also prints the pass count. Students change the string length and graph period against length.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Bright 4-digit 7-segment display driven by two wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_pendulum_period.inoVerify & upload in Electrolark// Pendulum period timer
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "class-pendulum-period"
#include <TM1637Display.h>
// ---- pins ----
const uint8_t HALL_PIN = 2;
const uint8_t SEG_CLK = 3;
const uint8_t SEG_DIO = 4;
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
bool magnet = false;
unsigned long lastPass = 0, periodMs = 0;
int passes = 0;
bool wasNear = false;
void setup() {
Serial.begin(115200);
pinMode(HALL_PIN, INPUT);
seg.setBrightness(5);
seg.clear();
seg.showNumberDec(0);
}
void loop() {
bool near = digitalRead(HALL_PIN) == LOW; // magnet on the bob is over the sensor
if (near && !wasNear && millis() - lastPass > 150) {
unsigned long now = millis();
if (lastPass) periodMs = (now - lastPass) * 2; // the bob passes twice per full swing (once each way)
lastPass = now;
passes++;
seg.showNumberDec(periodMs ? (int)periodMs : passes, false); // shows the period in ms once two passes are known
Serial.print(F("Pass ")); Serial.print(passes); Serial.print(F(" period ")); Serial.print(periodMs); Serial.println(F(" ms"));
}
wasNear = near;
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Flip the magnet and adjust the trimmer.
CLK and DIO swapped; swap them.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Vary length from 20 to 100 cm; the square-root relationship is a good extension.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), Linear Magnetic Hall Sensor Module – LM393, TM1637 4-Digit 7-Segment Display Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1 hour. The build on this page has 7 steps.
No. This page has the complete, tested code (class_pendulum_period.ino). Install this library first: TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹351 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Periodic motion; Variables.
Ideas that reuse this build: Hall tachometer. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.