Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsUse the reaction game with the lights on and then off. Students collect ten attempts in each condition and compare averages.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Bright 4-digit 7-segment display driven by two wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_reaction_light_dark.inoVerify & upload in Electrolark// Does light affect your reaction time?
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-reaction-light-dark"
#include <TM1637Display.h>
// ---- pins ----
const uint8_t BUTTON_PIN = 2;
const uint8_t SEG_CLK = 3;
const uint8_t SEG_DIO = 4;
const uint8_t LED_RED = 5;
TM1637Display seg(SEG_CLK, SEG_DIO);
unsigned long best = 9999;
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void waitRelease() { while (digitalRead(BUTTON_PIN) == LOW) delay(5); }
void setup() {
Serial.begin(115200);
pinMode(BUTTON_PIN, INPUT_PULLUP);
seg.setBrightness(5);
seg.clear();
pinMode(LED_RED, OUTPUT);
randomSeed(analogRead(A0) + micros());
seg.showNumberDec(0);
}
void loop() {
// press to start a round
if (digitalRead(BUTTON_PIN) != LOW) return;
waitRelease();
seg.clear();
setRedLed(false);
unsigned long waitUntil = millis() + random(1500, 5000);
while (millis() < waitUntil) {
if (digitalRead(BUTTON_PIN) == LOW) { // jumped the gun
seg.showNumberDec(0);
for (int i = 0; i < 4; i++) { setRedLed(true); delay(100); setRedLed(false); delay(100); }
waitRelease();
return;
}
}
setRedLed(true);
unsigned long start = millis();
while (digitalRead(BUTTON_PIN) != LOW) {}
unsigned long ms = millis() - start;
setRedLed(false);
seg.showNumberDec(ms);
if (ms < best) best = ms;
Serial.print(F("Reaction: ")); Serial.print(ms); Serial.print(F(" ms best: ")); Serial.println(best);
waitRelease();
delay(500);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The button is rotated 90°; legs on the same side are already connected. Turn it.
CLK and DIO swapped; swap them.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Collect class data in a table and find the mean for each condition.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Tactile Push Button Switch, TM1637 4-Digit 7-Segment Display Module, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (class_reaction_light_dark.ino). Install this library first: TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹432 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Experimental design; Statistics.
Ideas that reuse this build: Reaction timer game. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.