Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsColour on screens is additive: red plus green gives yellow. Students predict the combination for orange, cyan and white, then check with the knobs.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Knob that sets how much red is in the mix.; Knob that sets how much green is in the mix.; Knob that sets how much blue is in the mix.
Sixteen individually addressable RGB LEDs on one data wire.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_rgb_colour_mixer.inoVerify & upload in Electrolark// RGB colour mixer
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-rgb-colour-mixer"
#include <Adafruit_NeoPixel.h>
// ---- pins ----
const uint8_t POT_RED = A0;
const uint8_t POT_GREEN = A1;
const uint8_t POT_BLUE = A2;
const uint8_t RING_PIN = 2;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
const int RING_LEDS = 16;
Adafruit_NeoPixel ring(RING_LEDS, RING_PIN, NEO_GRB + NEO_KHZ800);
void showLevel(int pct, uint32_t color) {
int lit = constrain(pct, 0, 100) * RING_LEDS / 100;
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, i < lit ? color : 0);
ring.show();
}
void setup() {
Serial.begin(115200);
ring.begin();
ring.setBrightness(40);
ring.show();
}
void loop() {
int r = map(analogRead(POT_RED), 0, ADC_MAX, 0, 255);
int g = map(analogRead(POT_GREEN), 0, ADC_MAX, 0, 255);
int bl = map(analogRead(POT_BLUE), 0, ADC_MAX, 0, 255);
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, ring.Color(r, g, bl));
ring.show();
Serial.print(F("R ")); Serial.print(r); Serial.print(F(" G ")); Serial.print(g); Serial.print(F(" B ")); Serial.println(bl);
delay(50);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The wiper is on an outer pin. Move the signal wire to the middle leg.
Add the 330 Ω resistor in series with DIN and share GND with the board.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Make a colour wheel worksheet to fill in.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, 3 × 16mm Rotary Potentiometer 10kΩ (Linear), WS2812 RGB LED Ring (16 LEDs), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 9 steps.
No. This page has the complete, tested code (class_rgb_colour_mixer.ino). Install this library first: Adafruit NeoPixel.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹446 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Additive colour; Analog inputs.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
G 127 B 127 R 127 G 127 B 127 R 127 G 127 B 127 R 127 G 127 B 127 R 127 G 127 B 127 R 127 G 127 B 127 R 127 G 127 B 127
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.