Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsStudents turn the knob and watch the segments change; they then draw each digit from segments on paper.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
A 10 kΩ knob that works as a voltage divider, giving an analog value you can map to anything.
Bright 4-digit 7-segment display driven by two wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_seven_segment_lab.inoVerify & upload in Electrolark// Seven-segment display lab
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-seven-segment-lab"
#include <TM1637Display.h>
// ---- pins ----
const uint8_t POT_PIN = A0;
const uint8_t SEG_CLK = 2;
const uint8_t SEG_DIO = 3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
int potPct = 0;
void setup() {
Serial.begin(115200);
seg.setBrightness(5);
seg.clear();
}
void loop() {
int n = map(analogRead(POT_PIN), 0, ADC_MAX, 0, 9999);
seg.showNumberDec(n, false);
delay(50);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The wiper is on an outer pin. Move the signal wire to the middle leg.
CLK and DIO swapped; swap them.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Make a table of which segments each digit uses.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, 16mm Rotary Potentiometer 10kΩ (Linear), TM1637 4-Digit 7-Segment Display Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 30 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (class_seven_segment_lab.ino). Install this library first: TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹391 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Number display; Segments.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.