Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsComputer science made visible: each press performs one more comparison step. Students predict which swap comes next.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Three indicator LEDs, each through a 330 Ω resistor to its pin.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_sorting_algorithm_lights.inoVerify & upload in Electrolark// Sorting with lights
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-sorting-algorithm-lights"
// ---- pins ----
const uint8_t LED_RED = 2;
const uint8_t LED_YELLOW = 3;
const uint8_t LED_GREEN = 4;
const uint8_t BUTTON_PIN = 5;
int vals[3];
int step = 0;
bool wasDown = false;
int ia = 0; // bubble sort position
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setYellowLed(bool on) { digitalWrite(LED_YELLOW, on ? HIGH : LOW); }
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void setLed(int n, bool on) { if (n == 1) setRedLed(on); else if (n == 2) setYellowLed(on); else setGreenLed(on); }
void shuffleVals() {
vals[0] = 1; vals[1] = 2; vals[2] = 3;
for (int i = 2; i > 0; i--) { int j = random(i + 1); int t = vals[i]; vals[i] = vals[j]; vals[j] = t; }
ia = 0;
Serial.print(F("New list: ")); for (int i = 0; i < 3; i++) { Serial.print(vals[i]); Serial.print(' '); } Serial.println();
}
bool sortedNow() { return vals[0] < vals[1] && vals[1] < vals[2]; }
void showVals() {
// Each LED lights with brightness steps: here we simply show which two positions are being compared
digitalWrite(LED_RED, ia == 0);
digitalWrite(LED_YELLOW, true);
digitalWrite(LED_GREEN, ia == 1);
}
void setup() {
Serial.begin(115200);
pinMode(LED_RED, OUTPUT); pinMode(LED_YELLOW, OUTPUT); pinMode(LED_GREEN, OUTPUT);
pinMode(BUTTON_PIN, INPUT_PULLUP);
randomSeed(analogRead(A0));
shuffleVals();
showVals();
}
void loop() {
bool down = digitalRead(BUTTON_PIN) == LOW;
if (down && !wasDown) {
if (sortedNow()) { shuffleVals(); }
else {
Serial.print(F("Compare positions ")); Serial.print(ia + 1); Serial.print(F(" and ")); Serial.print(ia + 2); Serial.print(F(": "));
if (vals[ia] > vals[ia + 1]) { int t = vals[ia]; vals[ia] = vals[ia + 1]; vals[ia + 1] = t; Serial.println(F("swap")); }
else Serial.println(F("already in order"));
ia = (ia + 1) % 2;
for (int i = 0; i < 3; i++) { Serial.print(vals[i]); Serial.print(' '); } Serial.println();
if (sortedNow()) { Serial.println(F("Sorted!")); digitalWrite(LED_RED, HIGH); digitalWrite(LED_YELLOW, HIGH); digitalWrite(LED_GREEN, HIGH); }
else showVals();
}
delay(30);
}
wasDown = down;
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
It is backwards: the long leg goes to the resistor.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Have students physically act out the sort first.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Through-Hole LED Pack (Pack of 10), Tactile Push Button Switch, Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1 hour. The build on this page has 6 steps.
No. This page has the complete, tested code (class_sorting_algorithm_lights.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹377 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Algorithms; Sorting.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
New list: 3 2 1
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.