Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsA truth table comes alive: press the buttons and see which LEDs light. Red lights only when all three buttons are pressed (AND), yellow when any is pressed (OR), green when an odd number are pressed (XOR). Students verify each truth table, with two or three inputs.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Three momentary buttons, one leg each to a pin and the other legs joined to GND; the internal pull-ups do the rest.
Three indicator LEDs, each through a 330 Ω resistor to its pin.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_switch_logic.inoVerify & upload in Electrolark// Logic gates with switches
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-switch-logic"
// ---- pins ----
const uint8_t BTN_1 = 2;
const uint8_t BTN_2 = 3;
const uint8_t BTN_3 = 4;
const uint8_t LED_RED = 5;
const uint8_t LED_YELLOW = 6;
const uint8_t LED_GREEN = 7;
// Buttons 1, 2, 3 are the inputs A, B, C.
// Red = A AND B AND C, yellow = A OR B OR C, green = XOR (an odd number of buttons pressed).
bool lastA = false, lastB = false, lastC = false;
// returns 0 when nothing is pressed, else 1-3
int pressedButton() {
if (digitalRead(BTN_1) == LOW) return 1;
if (digitalRead(BTN_2) == LOW) return 2;
if (digitalRead(BTN_3) == LOW) return 3;
return 0;
}
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setYellowLed(bool on) { digitalWrite(LED_YELLOW, on ? HIGH : LOW); }
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void setLed(int n, bool on) { if (n == 1) setRedLed(on); else if (n == 2) setYellowLed(on); else setGreenLed(on); }
void setup() {
Serial.begin(115200);
pinMode(BTN_1, INPUT_PULLUP); pinMode(BTN_2, INPUT_PULLUP); pinMode(BTN_3, INPUT_PULLUP);
pinMode(LED_RED, OUTPUT); pinMode(LED_YELLOW, OUTPUT); pinMode(LED_GREEN, OUTPUT);
}
void loop() {
bool a = digitalRead(BTN_1) == LOW;
bool bb = digitalRead(BTN_2) == LOW;
bool cc = digitalRead(BTN_3) == LOW;
bool andOut = a && bb && cc, orOut = a || bb || cc, xorOut = (a + bb + cc) % 2 == 1;
digitalWrite(LED_RED, andOut);
digitalWrite(LED_YELLOW, orOut);
digitalWrite(LED_GREEN, xorOut);
if (a != lastA || bb != lastB || cc != lastC) {
Serial.print(F("A=")); Serial.print(a); Serial.print(F(" B=")); Serial.print(bb); Serial.print(F(" C=")); Serial.print(cc);
Serial.print(F(" AND=")); Serial.print(andOut); Serial.print(F(" OR=")); Serial.print(orOut); Serial.print(F(" XOR=")); Serial.println(xorOut);
lastA = a; lastB = bb; lastC = cc;
}
delay(10);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
It is rotated 90°; turn it so the legs span the gap.
It is backwards: the long leg goes to the resistor.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Have students fill in the truth tables before pressing.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, 3 × Tactile Push Button Switch, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (class_switch_logic.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹391 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Boolean logic; Truth tables.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.