LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe load cell bends slightly under weight and the HX711 measures the change. Students calibrate with a known mass and weigh a set of objects.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
A strain-gauge bar that bends very slightly under load, and a 24-bit HX711 amplifier that turns that into a weight.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_weigh_it.inoVerify & upload in Electrolark// Digital scale lab
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-weigh-it"
#include <HX711.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t HX_DT = 2;
const uint8_t HX_SCK = 3;
HX711 scale;
const float CALIBRATION = 420.0; // raw units per gram: calibrate with a known weight
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float grams = 0;
const unsigned long READ_EVERY_MS = 200;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Weight"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 16);
oled.print(F("Weight"));
oled.setTextSize(2);
oled.setCursor(0, 28);
oled.print(grams, 0);
oled.print(F(" g"));
oled.setTextSize(1);
oled.display();
}
void setup() {
Serial.begin(115200);
scale.begin(HX_DT, HX_SCK);
scale.set_scale(CALIBRATION);
scale.tare(); // empty platform = 0 g
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
grams = scale.get_units(5);
Serial.print(F("Weight="));
Serial.print(grams, 0);
Serial.print(F("g"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Let it warm up for a minute and avoid touching the wires; re-tare after warm-up.
Place a known weight and adjust CALIBRATION until the reading matches.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Compare against a kitchen scale and compute the percentage error.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, 5kg Load Cell Kit with HX711 Module, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1 hour. The build on this page has 7 steps.
No. This page has the complete, tested code (class_weigh_it.ino). Install these libraries first: HX711, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹988 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Calibration; Measurement error.
Ideas that reuse this build: Kitchen scale. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Weight=500g Weight=500g Weight=500g Weight=500g Weight=500g Weight=500g Weight=500g Weight=500g Weight=500g
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.