LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsCutting tiles, sanding walls and breaking concrete fill the air with fine dust. The sensor on a tripod shows the reading on the LCD and chirps with a red light when it climbs, which reminds workers to put on masks and wet the work area.
A reminder aid, not a certified dust monitor. Workers should wear proper masks whenever there is visible dust.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Optical dust sensor: an infrared LED shines across a small chamber and a photodiode measures the light scattered by smoke, dust and pollen.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
150 Ω resistor on the LED supply; 220 Ω series resistor for each LED
Follow the colours: red is power, dark grey is ground, blue is a signal.
construction_dust_alarm.inoVerify & upload in Electrolark// Construction dust alarm
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "construction-dust-alarm"
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t DUST_LED = 2;
const uint8_t DUST_PIN = A0;
const uint8_t BUZZER_PIN = 3;
const uint8_t LED_RED = 4;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float dustUg = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 200; // set well above the clean-air reading in your area
const float HYSTERESIS = 40; // gap that stops rapid on/off switching
float readDustUg() {
float v = 0;
for (int i = 0; i < 10; i++) {
digitalWrite(DUST_LED, LOW); // LED on
delayMicroseconds(280);
v += analogRead(DUST_PIN);
delayMicroseconds(40);
digitalWrite(DUST_LED, HIGH); // LED off
delayMicroseconds(9680);
}
float volts = (v / 10.0f) * VREF / ADC_MAX;
float ug = (volts - 0.6f) * 200.0f; // about 0.5 V per 100 ug/m3 above a 0.6 V clean-air level
return ug < 0 ? 0 : ug;
}
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Dust "));
lcd.print(dustUg, 0);
lcd.print(F(" ug/m3"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(statusText);
lcd.print(F(" "));
}
void evaluate() {
if (!alertOn && dustUg > ALERT_LEVEL) alertOn = true;
else if (alertOn && dustUg < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "DUSTY" : "Air clear";
}
void setup() {
Serial.begin(115200);
pinMode(DUST_LED, OUTPUT);
digitalWrite(DUST_LED, HIGH); // LED off
lcd.init();
lcd.backlight();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
dustUg = readDustUg();
evaluate();
Serial.print(F("Dust="));
Serial.print(dustUg, 0);
Serial.print(F("ug/m3"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setRedLed(alertOn && (millis() / 250) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Dust has settled in the chamber. Blow gently into the air slots and let it settle.
Add the 220 µF capacitor on the LED supply and keep the Vo wire short.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Nano CH340 Development Board (Soldered), Sharp GP2Y1010AU0F PM2.5 Dust & Smoke Particle Sensor Module, LCD1602 16x2 Character LCD (blue, with I2C adapter), Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Electrolytic Capacitor, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 10 steps.
No. This page has the complete, tested code (construction_dust_alarm.ino). Install this library first: LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹851 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Character displays and I²C backpacks; Current-limiting resistors for LEDs; Optical scattering and pulsed measurement.
A reminder aid, not a certified dust monitor. Workers should wear proper masks whenever there is visible dust.
Ideas that reuse this build: Dust sensor air monitor and Workshop dust and air alarm. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Dust=180ug/m3, status=Air clear Dust=180ug/m3, status=Air clear
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.