Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsWild boar and nilgai raid crops at night. The PIR watches the fence gap; after dark, any movement switches the relay that lights a 12 V floodlight for a minute and sounds the buzzer. In the daytime the LDR keeps it quiet.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Passive infrared sensor that detects the body heat of moving people or animals up to about 7 m away.
Light-dependent resistor with a comparator: its output flips when the light falls below the level set by the trimmer.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
12 V supply for a 12 V LED floodlight on the relay
Follow the colours: red is power, dark grey is ground, blue is a signal.
field_fence_intrusion_light.inoVerify & upload in Electrolark// Field fence intrusion floodlight
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "field-fence-intrusion-light"
// ---- pins ----
const uint8_t PIR_PIN = 2;
const uint8_t LDR_PIN = 3;
const uint8_t RELAY_PIN = 4;
const uint8_t BUZZER_PIN = 5;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
bool motion = false;
bool dark = false;
const unsigned long READ_EVERY_MS = 50;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const unsigned long HOLD_MS = 60000; // stay on this long after the last trigger
unsigned long lastTrigger = 0;
const unsigned long WARMUP_MS = 30000UL; // sensor warm-up
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void evaluate() {
if (millis() < WARMUP_MS) { alertOn = false; statusText = "Warming up"; return; }
if (motion && dark) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "INTRUDER" : "OK";
}
void setup() {
Serial.begin(115200);
pinMode(PIR_PIN, INPUT);
pinMode(LDR_PIN, INPUT);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
motion = digitalRead(PIR_PIN) == HIGH;
dark = digitalRead(LDR_PIN) == HIGH;
evaluate();
Serial.print(F("Motion="));
Serial.print(motion ? F("yes") : F("no"));
Serial.print(F(", Dark="));
Serial.print(dark ? F("yes") : F("no"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setRelay(alertOn);
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Give it a minute to settle after power-up and keep it away from heaters, windows and fans.
Turn the sensitivity (Sx) pot clockwise and check the module has 5 V on VCC.
Some modules invert DO. Change == HIGH to == LOW in the code.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Nano CH340 Development Board (Soldered), HC-SR501 PIR Motion Detector Sensor Module, Digital LDR Light Sensor Module – LM393, 5V Relay Module with Optocoupler (1 channel), Active Buzzer Module 3.3–5V, DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (field_fence_intrusion_light.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹645 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Digital inputs and sensor hold time; Isolation, relays and switching higher-power loads; Thresholds set in hardware vs software.
Ideas that reuse this build: Crop scarer and Automatic dusk-to-dawn light. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
, Dark=no, status=Warming up Motion=no, Dark=no, status=Warming up Motion=no, Dark=no, status=Warming up Motion=no, Dark=no, status=Warming up Motion=no, Dark=no, status=Warming up Motion=no, Dark=no, status=Warming up Motion=no, Dark=no, status=Warming up
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.