LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe GPS module works out its position from satellites. At the first good fix the sketch saves that point as home; after that, every two seconds it calculates the distance from home and sounds the buzzer when it passes 200 m. Use it to learn about GPS and geofencing, or add an SMS module so the alert reaches your phone.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
GPS receiver that outputs position, speed, altitude and UTC time once it sees at least 4 satellites.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
gps_geofence_alarm.inoVerify & upload in Electrolark// GPS geofence alarm for vehicles and cattle
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "gps-geofence-alarm"
#include <TinyGPSPlus.h>
#include <SoftwareSerial.h>
// ---- pins ----
const uint8_t GPS_RX = 2;
const uint8_t GPS_TX = 3;
const uint8_t BUZZER_PIN = 4;
const uint8_t LED_RED = 5;
TinyGPSPlus gps;
SoftwareSerial gpsSerial(GPS_RX, GPS_TX);
double homeLat = 0, homeLon = 0; // set automatically at the first good fix, or type yours here
const double RADIUS_M = 200; // alarm when further than this from home
bool homeSet = false, outside = false;
unsigned long lastCheck = 0;
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
gpsSerial.begin(9600);
}
void loop() {
while (gpsSerial.available()) gps.encode(gpsSerial.read());
if (millis() - lastCheck < 2000) return;
lastCheck = millis();
if (!gps.location.isValid() || gps.satellites.value() < 4) { Serial.println(F("Waiting for GPS fix")); return; }
double lat = gps.location.lat(), lon = gps.location.lng();
if (!homeSet) { if (homeLat == 0) { homeLat = lat; homeLon = lon; } homeSet = true; Serial.println(F("Home set")); }
double d = TinyGPSPlus::distanceBetween(lat, lon, homeLat, homeLon);
outside = d > RADIUS_M;
setBuzzer(outside && (millis() / 500) % 2 == 0);
setRedLed(outside);
Serial.print(F("Distance from home ")); Serial.print(d, 0); Serial.println(outside ? F(" m: OUTSIDE") : F(" m"));
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
GPS needs open sky. Test near a window or outside; the first cold start can take several minutes.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, GY-NEO6MV2 GPS Module with u-blox NEO-6M & Antenna, Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (gps_geofence_alarm.ino). Install this library first: TinyGPSPlus.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹746 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; NMEA sentences and GNSS fixes.
Ideas that reuse this build: GPS speedometer and SMS intruder alert. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Home set Distance from home 0 m
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.