GPS speedometer and clock
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Shop by category
Shop all componentsA bike or car odometer measures wheel turns. This one adds up the distance between GPS positions instead, ignoring the drift when you stand still. The LCD shows the trip in kilometres and the highest speed, and the button resets for the next ride.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
GPS receiver that outputs position, speed, altitude and UTC time once it sees at least 4 satellites.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
gps_trip_odometer.inoVerify & upload in Electrolark// GPS trip odometer and top speed
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "gps-trip-odometer"
#include <TinyGPSPlus.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
#include <SoftwareSerial.h>
// ---- pins ----
const uint8_t GPS_RX = 2;
const uint8_t GPS_TX = 3;
const uint8_t BUTTON_PIN = 4;
TinyGPSPlus gps;
LiquidCrystal_I2C lcd(0x27, 16, 2);
SoftwareSerial gpsSerial(GPS_RX, GPS_TX);
double lastLat = 0, lastLon = 0;
bool haveLast = false;
double tripKm = 0;
float topKmph = 0;
unsigned long lastShow = 0;
void setup() {
Serial.begin(115200);
lcd.init();
lcd.backlight();
pinMode(BUTTON_PIN, INPUT_PULLUP);
gpsSerial.begin(9600);
lcd.clear(); lcd.print(F("Waiting for GPS"));
}
void loop() {
while (gpsSerial.available()) gps.encode(gpsSerial.read());
if (digitalRead(BUTTON_PIN) == LOW) { tripKm = 0; topKmph = 0; haveLast = false; delay(300); } // button resets the trip
if (gps.location.isUpdated() && gps.location.isValid() && gps.satellites.value() >= 4) {
double lat = gps.location.lat(), lon = gps.location.lng();
float kmph = gps.speed.kmph();
if (haveLast && kmph > 2.0) tripKm += TinyGPSPlus::distanceBetween(lat, lon, lastLat, lastLon) / 1000.0; // ignore drift when standing still
lastLat = lat; lastLon = lon; haveLast = true;
if (kmph > topKmph) topKmph = kmph;
}
if (millis() - lastShow < 1000) return;
lastShow = millis();
lcd.clear();
if (!haveLast) { lcd.print(F("Waiting for GPS")); return; }
lcd.print(F("Trip ")); lcd.print(tripKm, 2); lcd.print(F(" km"));
lcd.setCursor(0, 1); lcd.print(F("Top ")); lcd.print(topKmph, 0); lcd.print(F(" km/h"));
Serial.print(F("Trip km ")); Serial.println(tripKm, 3);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
GPS needs open sky. Test near a window or outside; the first cold start can take several minutes.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, GY-NEO6MV2 GPS Module with u-blox NEO-6M & Antenna, LCD1602 16x2 Character LCD (blue, with I2C adapter), Tactile Push Button Switch, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (gps_trip_odometer.ino). Install these libraries first: TinyGPSPlus and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹787 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Character displays and I²C backpacks; NMEA sentences and GNSS fixes; Pull-ups and debouncing.
Ideas that reuse this build: GPS speedometer and GPS route logger. They are listed under Take it further on this page.
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Records where you went every five seconds, ready to open on a map.
Two boards, two radios: press the button at the gate and it rings indoors.
Check temperature, humidity and pressure from any phone on your Wi-Fi.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Trip km 0.000 Trip km 0.000
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.