Double-clap light switch
Clap twice and the lights come on. Clap twice again to switch them off.
Shop by category
Shop all componentsA theremin is played without touching it. Here the ultrasonic sensor measures the distance to your hand and the Uno maps 5 to 50 cm onto a pitch, from a low hum to a high whistle. Move slowly for glides, quickly for jumps.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Sends a 40 kHz ultrasonic ping and times the echo to measure distance from 2 cm to about 4 m.
Follow the colours: red is power, dark grey is ground, blue is a signal.
hand_theremin.inoVerify & upload in Electrolark// Ultrasonic hand theremin
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "hand-theremin"
// ---- pins ----
const uint8_t TRIG_PIN = 2;
const uint8_t ECHO_PIN = 3;
const uint8_t PIEZO_PIN = 4;
const uint8_t LED_RED = 5;
// ---- latest readings ----
float distCm = 0;
float smoothCm = 30;
float readDistanceCm() {
digitalWrite(TRIG_PIN, LOW);
delayMicroseconds(2);
digitalWrite(TRIG_PIN, HIGH);
delayMicroseconds(10);
digitalWrite(TRIG_PIN, LOW);
unsigned long us = pulseIn(ECHO_PIN, HIGH, 30000UL); // 30 ms timeout, about 5 m
if (us == 0) return -1; // no echo
return us * 0.0343f / 2.0f;
}
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(TRIG_PIN, OUTPUT);
pinMode(ECHO_PIN, INPUT);
pinMode(LED_RED, OUTPUT);
}
void loop() {
distCm = readDistanceCm();
if (distCm > 0 && distCm < 50) {
smoothCm = smoothCm * 0.6f + distCm * 0.4f;
int freq = map((int)(smoothCm * 10), 50, 500, 1200, 150); // nearer hand = higher note
tone(PIEZO_PIN, freq);
setRedLed(true);
} else { noTone(PIEZO_PIN); setRedLed(false); }
delay(30);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
TRIG and ECHO are swapped, or the sensor has no 5 V. Swap the two signal wires and check VCC.
Average several readings and keep wires short. Two HC-SR04s pinging at once will confuse each other.
Normal for a bare piezo; mount it on a small box to resonate.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, HC-SR04 Ultrasonic Range Finder Sensor Module, Piezo Buzzer (passive), Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 8 steps.
No. This page has the complete, tested code (hand_theremin.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹453 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Current-limiting resistors for LEDs; Generating musical notes with tone(); Time-of-flight measurement with sound.
Ideas that reuse this build: Louder version with an amplifier and Keypad piano. They are listed under Take it further on this page.
Clap twice and the lights come on. Clap twice again to switch them off.
Plays a friendly ding-dong whenever someone walks into the shop or room.
Beeps and flashes any message in Morse, or key your own by hand.
Turn a membrane keypad into a two-octave piano.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.