LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsSmall producers lose money on over-filled jars. The jar stands on the scale; press the button and the solenoid valve opens until the jar holds 500 g, closing slightly early because thick honey keeps flowing. The LCD shows the weight as it fills.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
A strain-gauge bar that bends very slightly under load, and a 24-bit HX711 amplifier that turns that into a weight.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
12 V solenoid valve under the honey tank
Follow the colours: red is power, dark grey is ground, blue is a signal.
honey_jar_filling_scale.inoVerify & upload in Electrolark// Honey jar filling scale
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "honey-jar-filling-scale"
#include <HX711.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t HX_DT = 2;
const uint8_t HX_SCK = 3;
const uint8_t RELAY_PIN = 4;
const uint8_t BUTTON_PIN = 5;
HX711 scale;
const float CALIBRATION = 420.0; // raw units per gram: calibrate with a known weight
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float grams = 0;
const float TARGET_G = 500; // 500 g jars
const float PREFLOW_G = 25; // material still falling when the feeder stops: stop this much early
bool filling = false;
unsigned long lastShow = 0;
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
scale.begin(HX_DT, HX_SCK);
scale.set_scale(CALIBRATION);
scale.tare(); // empty platform = 0 g
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
lcd.init();
lcd.backlight();
pinMode(BUTTON_PIN, INPUT_PULLUP);
setRelay(false);
}
void loop() {
if (!filling && digitalRead(BUTTON_PIN) == LOW) { // place an empty bag, then press
scale.tare(); filling = true; Serial.println(F("Filling")); delay(300);
}
grams = scale.get_units(5);
if (filling && grams >= TARGET_G - PREFLOW_G) { filling = false; Serial.print(F("Done at ")); Serial.println(grams, 0); }
if (filling && digitalRead(BUTTON_PIN) == LOW) { filling = false; Serial.println(F("Stopped")); delay(300); }
setRelay(filling);
if (millis() - lastShow > 300) {
lastShow = millis();
char buf[17];
snprintf(buf, sizeof(buf), "%6d / %d g ", (int)grams, (int)TARGET_G);
lcd.setCursor(0, 0); lcd.print(buf);
lcd.setCursor(0, 1); lcd.print(filling ? F("Filling... ") : F("Press to fill "));
}
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Let it warm up for a minute and avoid touching the wires; re-tare after warm-up.
Place a known weight and adjust CALIBRATION until the reading matches.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
9 parts: Nano CH340 Development Board (Soldered), 5kg Load Cell Kit with HX711 Module, 5V Relay Module with Optocoupler (1 channel), LCD1602 16x2 Character LCD (blue, with I2C adapter), Tactile Push Button Switch, 12V Solenoid Water Valve 1/2" (Normally Closed), DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (honey_jar_filling_scale.ino). Install these libraries first: HX711 and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,409 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Character displays and I²C backpacks; Isolation, relays and switching higher-power loads; Pull-ups and debouncing; Strain gauges, amplifiers and calibration factors.
Ideas that reuse this build: Feed bag filler and Kitchen scale. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.