LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsFor a parent or grandparent who lives alone. The PIR watches the main room; from 7:00 to 22:00, four hours with no movement turn on the light and a periodic beep. Pressing the "I'm fine" button resets it. Night hours are ignored. It is a simple local version that a Wi-Fi board can later extend with a phone message.
A helpful reminder, not a medical alarm or a replacement for regular contact.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Passive infrared sensor that detects the body heat of moving people or animals up to about 7 m away.
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
inactivity_check_in_alarm.inoVerify & upload in Electrolark// Elderly inactivity check-in alarm
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "inactivity-check-in-alarm"
#include <Wire.h>
#include <RTClib.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t PIR_PIN = 2;
const uint8_t BUZZER_PIN = 3;
const uint8_t LED_RED = 4;
const uint8_t BUTTON_PIN = 5;
RTC_DS3231 rtc;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
bool motion = false;
const unsigned long QUIET_HOURS = 4; // daytime hours without movement before the alert
const int DAY_START_H = 7, DAY_END_H = 22; // no alerts at night
unsigned long lastMove = 0;
bool alert = false;
unsigned long lastShow = 0;
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(PIR_PIN, INPUT);
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
lcd.init();
lcd.backlight();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
pinMode(BUTTON_PIN, INPUT_PULLUP);
lastMove = millis();
setBuzzer(false);
}
void loop() {
motion = digitalRead(PIR_PIN) == HIGH;
DateTime now = rtc.now();
bool day = now.hour() >= DAY_START_H && now.hour() < DAY_END_H;
if (motion) { lastMove = millis(); }
if (day && millis() - lastMove > QUIET_HOURS * 3600000UL) alert = true;
if (alert && digitalRead(BUTTON_PIN) == LOW) { alert = false; lastMove = millis(); delay(300); } // "I'm fine" button
setRedLed(alert);
unsigned long t = millis() % 10000;
setBuzzer(alert && t < 1200 && (t / 200) % 2 == 0);
if (millis() - lastShow > 1000) {
lastShow = millis();
unsigned long quietMin = (millis() - lastMove) / 60000;
lcd.setCursor(0, 0); lcd.print(F("Quiet for ")); lcd.print(quietMin); lcd.print(F(" min "));
lcd.setCursor(0, 1); lcd.print(alert ? F("CHECK IN? Press ") : (day ? F("Watching (day) ") : F("Night: paused ")));
}
delay(50);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Give it a minute to settle after power-up and keep it away from heaters, windows and fans.
Turn the sensitivity (Sx) pot clockwise and check the module has 5 V on VCC.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
11 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, HC-SR501 PIR Motion Detector Sensor Module, DS3231 Precision RTC Module with EEPROM, LCD1602 16x2 Character LCD (blue, with I2C adapter), Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Tactile Push Button Switch, Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points), plus 1 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 12 steps.
No. This page has the complete, tested code (inactivity_check_in_alarm.ino). Install these libraries first: RTClib and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹700 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Character displays and I²C backpacks; Current-limiting resistors for LEDs; Digital inputs and sensor hold time; Pull-ups and debouncing.
A helpful reminder, not a medical alarm or a replacement for regular contact.
Ideas that reuse this build: Room occupancy dashboard and Medicine reminder. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.