Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsPWM changes the average power to an LED so it looks brighter or dimmer. The remote's up and down keys step the brightness by 10 per cent, and the on and off keys switch the lamp. A good first step towards remote-controlled lighting.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
38 kHz infrared receiver that decodes button codes from almost any TV or AC remote.
Red LED on a PWM-capable pin so its brightness can be set from 0 to 255.
Follow the colours: red is power, dark grey is ground, blue is a signal.
ir_remote_led_dimmer.inoVerify & upload in Electrolark// IR remote LED dimmer
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "ir-remote-led-dimmer"
#include <IRremote.hpp>
// ---- pins ----
const uint8_t IR_PIN = 2;
const uint8_t LED_RED = 3;
// Read your remote's codes with the IR code reader project, then put them here
const uint16_t CMD_UP = 0x46, CMD_DOWN = 0x15, CMD_ON = 0x45, CMD_OFF = 0x44;
int level = 128; // brightness 0 to 255
bool lit = true;
void apply() { analogWrite(LED_RED, lit ? level : 0); }
void setup() {
Serial.begin(115200);
IrReceiver.begin(IR_PIN);
pinMode(LED_RED, OUTPUT);
apply();
}
void loop() {
if (IrReceiver.decode()) {
uint16_t cmd = IrReceiver.decodedIRData.command;
IrReceiver.resume();
if (cmd == CMD_UP) { lit = true; level = min(255, level + 25); }
else if (cmd == CMD_DOWN) { level = max(5, level - 25); }
else if (cmd == CMD_ON) { lit = true; }
else if (cmd == CMD_OFF) { lit = false; }
else { Serial.print(F("Unused command 0x")); Serial.println(cmd, HEX); }
apply();
Serial.print(F("Brightness ")); Serial.println(lit ? level : 0);
}
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Point the remote straight at the receiver, check the OUT pin, and try a fresh remote battery.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Digital 38kHz Infrared Receiver Module, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (ir_remote_led_dimmer.ino). Install this library first: IRremote.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹411 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Current-limiting resistors for LEDs; Infrared remote protocols (NEC).
Ideas that reuse this build: IR remote mood light and IR code reader. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.