Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsSplitting a restaurant bill is a classic argument. The 4x4 keypad takes the figures in turn (A is the decimal point, * is backspace, # is enter), and the LCD shows the total and each person's share. Also a good practice project for typing numbers on a keypad.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
16-key membrane keypad scanned as a 4×4 grid, so 8 wires read 16 buttons.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
keypad_bill_splitter.inoVerify & upload in Electrolark// Keypad bill splitter with tip
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "keypad-bill-splitter"
#include <Keypad.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t KP_R1 = 2;
const uint8_t KP_R2 = 3;
const uint8_t KP_R3 = 4;
const uint8_t KP_R4 = 5;
const uint8_t KP_C1 = 6;
const uint8_t KP_C2 = 7;
const uint8_t KP_C3 = 8;
const uint8_t KP_C4 = 12;
const char KEYS[4][4] = {{'1','2','3','A'},{'4','5','6','B'},{'7','8','9','C'},{'*','0','#','D'}};
byte rowPins[4] = {KP_R1, KP_R2, KP_R3, KP_R4};
byte colPins[4] = {KP_C1, KP_C2, KP_C3, KP_C4};
Keypad keypad = Keypad(makeKeymap(KEYS), rowPins, colPins, 4, 4);
LiquidCrystal_I2C lcd(0x27, 16, 2);
// Reads a number typed on the keypad: digits, * = backspace, # = enter, A = decimal point. Shows the prompt on line 1.
float askNumber(const char* prompt) {
char buf[10]; int n = 0; buf[0] = 0;
lcd.clear(); lcd.print(prompt);
while (true) {
char k = keypad.getKey();
if (!k) continue;
if (k >= '0' && k <= '9' && n < 8) { buf[n++] = k; buf[n] = 0; }
else if (k == 'A' && n < 8 && !strchr(buf, '.')) { buf[n++] = '.'; buf[n] = 0; }
else if (k == '*' && n > 0) { buf[--n] = 0; }
else if (k == '#' && n > 0) { return atof(buf); }
lcd.setCursor(0, 1); lcd.print(F(" ")); lcd.setCursor(0, 1); lcd.print(buf);
}
}
void setup() {
Serial.begin(115200);
lcd.init();
lcd.backlight();
}
void loop() {
float bill = askNumber("Bill amount?");
float people = askNumber("How many people?");
if (people < 1) people = 1;
float tip = askNumber("Tip %? (0 for none)");
float total = bill * (1 + tip / 100.0f);
lcd.clear(); lcd.print(F("Total ")); lcd.print(total, 2);
lcd.setCursor(0, 1); lcd.print(F("Each ")); lcd.print(total / people, 2);
Serial.print(F("Total ")); Serial.print(total, 2); Serial.print(F(" each ")); Serial.println(total / people, 2);
while (keypad.getKey() == NO_KEY) {} // any key to start again
delay(200);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Rows and columns are swapped or reversed; swap the rowPins and colPins lists.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Membrane Matrix Keypad (4x4), LCD1602 16x2 Character LCD (blue, with I2C adapter), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (keypad_bill_splitter.ino). Install these libraries first: Keypad and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹480 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Character displays and I²C backpacks; Matrix scanning.
Ideas that reuse this build: Maths quiz machine and Keypad calculator. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.