LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe VL53L1X laser sensor measures the distance down to the water surface through a small hole. When the distance passes the low mark the relay starts the pump, and when it falls below the high mark the pump stops.
Field pumps run on mains or three-phase power. Have a licensed electrician fit a contactor and starter: never connect them to the relay module directly.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Laser time-of-flight sensor that measures distance up to about 4 m with millimetre resolution and a narrow beam.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Mini pump for the bench model (a field pump goes through a contactor)
Follow the colours: red is power, dark grey is ground, blue is a signal.
The bench model runs the 3–6 V mini pump from a 4×AA holder through the relay (COM and NO). A mains or three-phase field pump must be switched by a contactor that an electrician wires; the relay only drives the contactor coil circuit he provides.
laser_tank_refill_pump.inoVerify & upload in Electrolark// Laser tank refill pump controller
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "laser-tank-refill-pump"
#include <Wire.h>
#include <VL53L1X.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t BUZZER_PIN = 2;
const uint8_t RELAY_PIN = 3;
VL53L1X tof1;
LiquidCrystal_I2C lcd(0x27, 16, 2);
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
float distCm = 0;
const unsigned long READ_EVERY_MS = 200;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 90; // the distance to the water at the low mark
const float HYSTERESIS = 15; // gap that stops rapid on/off switching
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Distance "));
lcd.print(distCm, 0);
lcd.print(F(" cm"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(statusText);
lcd.print(F(" "));
}
void evaluate() {
if (!(distCm > 0)) { statusText = "Sensor error"; return; }
if (!alertOn && distCm > ALERT_LEVEL) alertOn = true;
else if (alertOn && distCm < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "FILLING" : "Tank OK";
}
void setup() {
Serial.begin(115200);
Wire.begin();
tof1.setTimeout(500);
if (!tof1.init()) Serial.println(F("VL53L1X not found"));
tof1.setDistanceMode(VL53L1X::Long);
tof1.setMeasurementTimingBudget(50000);
tof1.startContinuous(50);
lcd.init();
lcd.backlight();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
distCm = tof1.read() / 10.0f;
evaluate();
Serial.print(F("Distance="));
Serial.print(distCm, 0);
Serial.print(F("cm"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setRelay(alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x29.
Aim at a flat, light surface and keep it clear of other objects in the beam.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Low-triggered module: invert the logic in setBuzzer().
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
9 parts: Nano CH340 Development Board (Soldered), TOF400C VL53L1X Laser Ranging Sensor Module – I2C Interface, LCD1602 16x2 Character LCD (blue, with I2C adapter), Active Buzzer Module 3.3–5V, 5V Relay Module with Optocoupler (1 channel), Mini Submersible Water Pump 3–6V with 1m tube, Battery Holder (AA), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 10 steps.
No. This page has the complete, tested code (laser_tank_refill_pump.ino). Install these libraries first: VL53L1X and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,234 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Character displays and I²C backpacks; Isolation, relays and switching higher-power loads; Laser ranging with a narrow beam.
Ideas that reuse this build: Wi-Fi laser tank level monitor and Laser tank level meter. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Distance=40cm, status=Tank OK Distance=40cm, status=Tank OK Distance=40cm, status=Tank OK Distance=40cm, status=Tank OK Distance=40cm, status=Tank OK Distance=40cm, status=Tank OK Distance=40cm, status=Tank OK Distance=40cm, status=Tank OK
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.