LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA platform of four load cells sits under the cylinder. The sketch subtracts the tare weight stamped on the cylinder collar, so the LCD shows the gas that is actually left. When it drops below 2 kg the buzzer chirps once a minute and the screen says "Book refill".
Do not drill, heat or modify the cylinder or regulator. The scale only sits under it.
This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Four half-bridge cells under the platform corners share the load, so the scale reads up to 200 kg; Subtracts the empty cylinder weight so the display shows the gas that is left.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
lpg_cylinder_gas_meter.inoVerify & upload in Electrolark// LPG cylinder gas-left meter
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "lpg-cylinder-gas-meter"
#include <HX711.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t HX_DT = 2;
const uint8_t HX_SCK = 3;
const uint8_t BUZZER_PIN = 4;
HX711 scale;
const float CALIBRATION = 420.0; // raw units per gram: calibrate with a known weight
const float EMPTY_CYLINDER_G = 15300; // tare weight (TW) stamped on the cylinder collar, in grams
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float grams = 0;
float gasKg = 0;
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 2.0; // about two weeks of cooking left in a 14.2 kg cylinder
const float HYSTERESIS = 0.5; // gap that stops rapid on/off switching
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Weight "));
lcd.print(grams, 0);
lcd.print(F(" g"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(F("Gas "));
lcd.print(gasKg, 1);
lcd.print(F(" kg"));
lcd.print(F(" "));
lcd.print(statusText);
lcd.print(F(" "));
}
void evaluate() {
if (!alertOn && gasKg < ALERT_LEVEL) alertOn = true;
else if (alertOn && gasKg > ALERT_LEVEL + HYSTERESIS) alertOn = false;
statusText = alertOn ? "Book refill" : "Gas OK";
}
void setup() {
Serial.begin(115200);
scale.begin(HX_DT, HX_SCK);
scale.set_scale(CALIBRATION);
scale.tare(); // empty platform = 0 g
lcd.init();
lcd.backlight();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
grams = scale.get_units(5);
gasKg = (grams - EMPTY_CYLINDER_G) / 1000.0f;
evaluate();
Serial.print(F("Weight="));
Serial.print(grams, 0);
Serial.print(F("g"));
Serial.print(F(", Gas left="));
Serial.print(gasKg, 1);
Serial.print(F("kg"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Let it warm up for a minute and avoid touching the wires; re-tare after warm-up.
Place a known weight and adjust CALIBRATION until the reading matches.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, HX711 with 4 × 50 kg Half-Bridge Load Cells and Combinator Board, LCD1602 16x2 Character LCD (blue, with I2C adapter), Active Buzzer Module 3.3–5V, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a advanced project and takes about 3 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (lpg_cylinder_gas_meter.ino). Install these libraries first: HX711 and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹497 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Character displays and I²C backpacks; Strain gauges, amplifiers and calibration factors; Tare weight and net weight.
Do not drill, heat or modify the cylinder or regulator. The scale only sits under it. This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed.
Ideas that reuse this build: Phone dashboard version and Kitchen scale. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Weight=500g, Gas left=-14.8kg, status=Book refill
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.