LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA load cell under the bowl weighs the food. The OLED shows the weight in grams, and when it drops below 100 g the yellow light says it is time to top up. Useful when the family is out and a pet sitter wants to know whether the bowl is empty.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
A strain-gauge bar that bends very slightly under load, and a 24-bit HX711 amplifier that turns that into a weight.
Follow the colours: red is power, dark grey is ground, blue is a signal.
pet_food_bowl_low_alarm.inoVerify & upload in Electrolark// Pet food bowl low alarm
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "pet-food-bowl-low-alarm"
#include <HX711.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t HX_DT = 2;
const uint8_t HX_SCK = 3;
const uint8_t LED_YELLOW = 4;
HX711 scale;
const float CALIBRATION = 420.0; // raw units per gram: calibrate with a known weight
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float grams = 0;
const unsigned long READ_EVERY_MS = 500;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 100; // about 100 g is a small meal for a cat
const float HYSTERESIS = 30; // gap that stops rapid on/off switching
void setYellowLed(bool on) { digitalWrite(LED_YELLOW, on ? HIGH : LOW); }
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Pet bowl"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 16);
oled.print(F("Weight"));
oled.setTextSize(2);
oled.setCursor(0, 28);
oled.print(grams, 0);
oled.print(F(" g"));
oled.setTextSize(1);
oled.setCursor(0, 56);
oled.print(statusText);
oled.display();
}
void evaluate() {
if (!alertOn && grams < ALERT_LEVEL) alertOn = true;
else if (alertOn && grams > ALERT_LEVEL + HYSTERESIS) alertOn = false;
statusText = alertOn ? "REFILL BOWL" : "Food OK";
}
void setup() {
Serial.begin(115200);
scale.begin(HX_DT, HX_SCK);
scale.set_scale(CALIBRATION);
scale.tare(); // empty platform = 0 g
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
pinMode(LED_YELLOW, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
grams = scale.get_units(5);
evaluate();
Serial.print(F("Weight="));
Serial.print(grams, 0);
Serial.print(F("g"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setYellowLed(alertOn);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Let it warm up for a minute and avoid touching the wires; re-tare after warm-up.
Place a known weight and adjust CALIBRATION until the reading matches.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, 5kg Load Cell Kit with HX711 Module, 0.96" OLED Display 128x64 (I2C), Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (pet_food_bowl_low_alarm.ino). Install these libraries first: HX711, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,036 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Current-limiting resistors for LEDs; Drawing text on an I²C display; Strain gauges, amplifiers and calibration factors.
Ideas that reuse this build: Digital kitchen scale and Wi-Fi weighing scale. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Weight=500g, status=Food OK Weight=500g, status=Food OK Weight=500g, status=Food OK Weight=500g, status=Food OK Weight=500g, status=Food OK
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.