LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsShared tools go missing because nobody remembers who had them. A sticker tag on each tool and one RFID reader by the tool board solve it: the first scan marks the tool TAKEN OUT, the second marks it RETURNED, and the LCD always shows how many tools are out. A good start for school labs and makerspaces.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
13.56 MHz RFID/NFC reader that reads the unique ID of cards and key fobs held near it.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
rfid_tool_checkout_board.inoVerify & upload in Electrolark// RFID tool check-out board
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "rfid-tool-checkout-board"
#include <SPI.h>
#include <MFRC522.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t RFID_SS = 2;
const uint8_t RFID_RST = 3;
const uint8_t BUZZER_PIN = 4;
MFRC522 rfid(RFID_SS, RFID_RST);
LiquidCrystal_I2C lcd(0x27, 16, 2);
// Add one row per tool tag: its 4-byte UID (shown in the Serial Monitor when you scan it) and a name of up to 12 letters
struct Tool { byte uid[4]; const char* name; bool out; };
Tool TOOLS[] = {
{{0xDE, 0xAD, 0xBE, 0xEF}, "Drill", false},
{{0x12, 0x34, 0x56, 0x78}, "Hammer", false},
{{0xCA, 0xFE, 0xBA, 0xBE}, "Spanner set", false},
};
const int N_TOOLS = sizeof(TOOLS) / sizeof(TOOLS[0]);
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
int toolsOut() {
int n = 0;
for (int i = 0; i < N_TOOLS; i++) if (TOOLS[i].out) n++;
return n;
}
void showCount() {
lcd.clear(); lcd.print(F("Tools out: ")); lcd.print(toolsOut());
lcd.setCursor(0, 1); lcd.print(F("Scan a tool tag"));
}
void setup() {
Serial.begin(115200);
SPI.begin();
rfid.PCD_Init();
lcd.init();
lcd.backlight();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
showCount();
}
void loop() {
if (!rfid.PICC_IsNewCardPresent() || !rfid.PICC_ReadCardSerial()) return;
for (byte i = 0; i < rfid.uid.size; i++) { if (rfid.uid.uidByte[i] < 0x10) Serial.print('0'); Serial.print(rfid.uid.uidByte[i], HEX); Serial.print(' '); }
Serial.println();
int found = -1;
if (rfid.uid.size >= 4) for (int i = 0; i < N_TOOLS; i++) if (memcmp(rfid.uid.uidByte, TOOLS[i].uid, 4) == 0) found = i;
if (found < 0) {
lcd.clear(); lcd.print(F("Unknown tag"));
setBuzzer(true); delay(600); setBuzzer(false);
} else {
TOOLS[found].out = !TOOLS[found].out; // each scan flips the tool between in and out
lcd.clear(); lcd.print(TOOLS[found].name);
lcd.setCursor(0, 1); lcd.print(TOOLS[found].out ? F("TAKEN OUT") : F("RETURNED"));
setBuzzer(true); delay(TOOLS[found].out ? 120 : 300); setBuzzer(false);
}
delay(1200);
showCount();
rfid.PICC_HaltA();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check it is on 3.3 V and the SPI wires (SCK, MOSI, MISO) are on the hardware SPI pins.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, RC522 RFID Reader / Writer SPI Module with Card & Tag, LCD1602 16x2 Character LCD (blue, with I2C adapter), Active Buzzer Module 3.3–5V, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (rfid_tool_checkout_board.ino). Install these libraries first: MFRC522 and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹519 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Character displays and I²C backpacks; RFID, UIDs and SPI.
Ideas that reuse this build: RFID attendance logger and RFID door lock. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.