Double-clap light switch
Clap twice and the lights come on. Clap twice again to switch them off.
Shop by category
Shop all componentsOlder people often do not feel how hot a room has become, and heatstroke creeps up quietly. When the room passes 35 °C, the speaker reminds them to drink water and switch on the fan or cooler, and repeats every 15 minutes while the heat lasts. Record the messages in the family's own voice and language.
A reminder, not a medical device. In a heat wave, check on elders in person.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Plays MP3 files from a microSD card through its own small amplifier, on command from the board over serial.
Connects straight to SPK1 and SPK2 (the module has a small 3 W amplifier)
Follow the colours: red is power, dark grey is ground, blue is a signal.
room_heat_voice_warning.inoVerify & upload in Electrolark// Room heat voice warning for elders
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "room-heat-voice-warning"
#include <DHT.h>
#include <DFRobotDFPlayerMini.h>
#include <SoftwareSerial.h>
// ---- pins ----
const uint8_t DHT_PIN = 2;
const uint8_t MP3_RX = 3;
const uint8_t MP3_TX = 4;
DHT dht(DHT_PIN, DHT22);
DFRobotDFPlayerMini player;
// ---- latest readings ----
float tempC = 0;
float humidity = 0;
SoftwareSerial mp3Serial(MP3_RX, MP3_TX);
const int VOLUME = 22; // 0-30
const unsigned long QUIET_MS = 900000UL; // at least this long between messages
unsigned long lastPlay = 0;
bool played = false;
void setup() {
Serial.begin(115200);
dht.begin();
mp3Serial.begin(9600);
if (!player.begin(mp3Serial)) Serial.println(F("DFPlayer not found: check wiring and card"));
player.volume(VOLUME);
randomSeed(analogRead(A0));
}
void loop() {
tempC = dht.readTemperature();
if ((tempC > 35) && (!played || millis() - lastPlay > QUIET_MS)) {
int t = random(1, 3);
player.playMp3Folder(t); // plays /mp3/000t.mp3
played = true; lastPlay = millis();
Serial.print(F("Hot room: track ")); Serial.println(t);
}
delay(100);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
Check TX goes to the board RX pin and RX to the board TX pin, and that the card is inserted and FAT32.
Tracks are numbered by the order files were copied. Use the mp3 folder with 0001.mp3 names so the numbers are fixed.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Nano CH340 Development Board (Soldered), DHT22 Temperature & Humidity Sensor, DFPlayer Mini MP3 Player Module (MP3-TF-16P), Mini Speaker 8Ω 1W 40mm, microSD Memory Card Class 10 (16GB), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (room_heat_voice_warning.ino). Install these libraries first: DHT sensor library, Adafruit Unified Sensor and DFRobotDFPlayerMini.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,009 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Serial-controlled audio playback; Single-wire digital sensors and why some sensors need slow polling.
A reminder, not a medical device. In a heat wave, check on elders in person.
Ideas that reuse this build: Talking thermometer and Car cabin heat alarm. They are listed under Take it further on this page.
Clap twice and the lights come on. Clap twice again to switch them off.
Plays a friendly ding-dong whenever someone walks into the shop or room.
Beeps and flashes any message in Morse, or key your own by hand.
Turn a membrane keypad into a two-octave piano.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.