Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsEvery RC and robotics bench needs one. The knob sets the angle directly, the button switches to an automatic sweep to spot dead zones, and a third press centres the servo at 90° for fitting horns. The angle shows on the display.
Tick anything you already have and the total updates.
A 10 kΩ knob that works as a voltage divider, giving an analog value you can map to anything.
Small hobby servo that turns to any angle from 0 to 180° on command.
Bright 4-digit 7-segment display driven by two wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
servo_tester_7seg.inoVerify & upload in Electrolark// Servo tester with angle display
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "servo-tester-7seg"
#include <Servo.h>
#include <TM1637Display.h>
// ---- pins ----
const uint8_t POT_PIN = A0;
const uint8_t SERVO_PIN = 3;
const uint8_t SEG_CLK = 2;
const uint8_t SEG_DIO = 4;
const uint8_t BUTTON_PIN = 5;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
Servo servo;
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
int potPct = 0;
int mode = 0; // 0 = knob, 1 = sweep, 2 = centre
unsigned long lastShow = 0;
int sweepAngle = 0, sweepDir = 2;
void setup() {
Serial.begin(115200);
servo.attach(SERVO_PIN);
seg.setBrightness(5);
seg.clear();
pinMode(BUTTON_PIN, INPUT_PULLUP);
}
void loop() {
if (digitalRead(BUTTON_PIN) == LOW) { mode = (mode + 1) % 3; delay(300); }
int angle;
if (mode == 0) angle = map(analogRead(POT_PIN), 0, ADC_MAX, 0, 180);
else if (mode == 1) { sweepAngle += sweepDir; if (sweepAngle >= 180 || sweepAngle <= 0) sweepDir = -sweepDir; angle = sweepAngle; }
else angle = 90;
servo.write(angle);
if (millis() - lastShow > 100) {
lastShow = millis();
seg.showNumberDec(angle);
Serial.print(mode == 0 ? F("knob ") : mode == 1 ? F("sweep ") : F("centre ")); Serial.println(angle);
}
delay(15);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The wiper is on an outer pin. Move the signal wire to the middle leg.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
CLK and DIO swapped; swap them.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), 16mm Rotary Potentiometer 10kΩ (Linear), TowerPro SG90 9g Micro Servo (180°), TM1637 4-Digit 7-Segment Display Module, Tactile Push Button Switch, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 9 steps.
No. This page has the complete, tested code (servo_tester_7seg.ino). Install these libraries first: Servo and TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹433 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Multiplexed 7-segment displays; PWM pulses and servo control; Pull-ups and debouncing; Voltage dividers and analogRead().
Ideas that reuse this build: Servo knob control and Robotic arm. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
knob 90 knob 89 knob 90 knob 90 knob 90 knob 90 knob 90 knob 89 knob 89
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.