Line follower robot with L298N and TCRT5000
The classic robotics starter: a two-wheeled car that tracks a black line on its own.
Shop by category
Shop all componentsEach knob drives one joint: base rotation, shoulder, elbow and gripper. The sketch eases each servo towards its knob position, which makes the movement smooth, and limits each joint so the frame never hits its end stops.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Moves the arm base.; Moves the arm shoulder.; Moves the arm elbow.; Moves the arm gripper.
Knob that sets the base angle.; Knob that sets the shoulder angle.; Knob that sets the elbow angle.; Knob that sets the gripper angle.
Follow the colours: red is power, dark grey is ground, blue is a signal.
All four servo red wires go to the 4×AA pack +; pack − joins Uno GND. Four servos can draw over 1 A.
robotic_arm_knobs.inoVerify & upload in Electrolark// Four-axis robotic arm with knob control
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "robotic-arm-knobs"
#include <Servo.h>
// ---- pins ----
const uint8_t SERVO_BASE = 3;
const uint8_t SERVO_SHOULDER = 5;
const uint8_t SERVO_ELBOW = 6;
const uint8_t SERVO_GRIP = 9;
const uint8_t POT_BASE = A0;
const uint8_t POT_SHOULDER = A1;
const uint8_t POT_ELBOW = A2;
const uint8_t POT_GRIP = A3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
const uint8_t SERVO_PINS[4] = {SERVO_BASE, SERVO_SHOULDER, SERVO_ELBOW, SERVO_GRIP};
const uint8_t POT_PINS[4] = {POT_BASE, POT_SHOULDER, POT_ELBOW, POT_GRIP};
const int MIN_ANGLE[4] = {0, 30, 20, 40}; // protect the frame from hitting its end stops
const int MAX_ANGLE[4] = {180, 150, 160, 100};
Servo joint[4];
float smooth[4] = {90, 90, 90, 70};
void setup() {
Serial.begin(115200);
for (int i = 0; i < 4; i++) joint[i].attach(SERVO_PINS[i]);
}
void loop() {
for (int i = 0; i < 4; i++) {
int target = map(analogRead(POT_PINS[i]), 0, ADC_MAX, MIN_ANGLE[i], MAX_ANGLE[i]);
smooth[i] += (target - smooth[i]) * 0.15f; // ease towards the knob position
joint[i].write((int)smooth[i]);
}
delay(20);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
The wiper is on an outer pin. Move the signal wire to the middle leg.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, 4 × TowerPro SG90 9g Micro Servo (180°), 4 × 16mm Rotary Potentiometer 10kΩ (Linear), 4-DOF Robotic Arm Kit (for SG90 / MG90S), Battery Holder (AA), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Precision Screwdriver Set and Digital Multimeter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 4–5 hours. The build on this page has 14 steps.
No. This page has the complete, tested code (robotic_arm_knobs.ino). Install this library first: Servo.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,110 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
PWM pulses and servo control; Voltage dividers and analogRead().
Ideas that reuse this build: Single servo starter. They are listed under Take it further on this page.
The classic robotics starter: a two-wheeled car that tracks a black line on its own.
A robot that looks left and right with its ultrasonic "head" and picks the clearest way.
Roams a tabletop without ever driving off the edge.
Drive a 4WD car from your Android phone over Bluetooth.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.