Obstacle-avoiding robot
A robot that looks left and right with its ultrasonic "head" and picks the clearest way.
Shop by category
Shop all componentsTwo infrared sensors under the front of the chassis look for black tape. If the line drifts under the left sensor the robot steers left, and the same for the right. That simple rule is enough to follow curves and loops at a good speed.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Dual H-bridge that lets the board drive two DC motors forwards, backwards and at variable speed.
Two infrared reflectance sensors: black tape reflects little IR, white floor reflects a lot, so each output tells you which side the line is on.
Raises the cell's 3.0–4.2 V to a steady 5 V for the board
Follow the colours: red is power, dark grey is ground, blue is a signal.
Battery + to L298N 12V, battery − to L298N GND and Uno GND. Power the Uno from the L298N 5V output into the Uno 5V pin, or from USB while testing. Set the boost converter to 5.0 V with a multimeter before connecting the board. Cell + → boost IN+, cell − (TP4056 OUT−) → boost IN−, then boost OUT+ → board 5V pin and OUT− → GND. A bare 18650 (3.0–4.2 V) cannot run a 5 V board by itself.
line_follower_robot.inoVerify & upload in Electrolark// Line follower robot
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "line-follower-robot"
// ---- pins ----
const uint8_t ENA = 3;
const uint8_t IN1 = 2;
const uint8_t IN2 = 4;
const uint8_t IN3 = 6;
const uint8_t IN4 = 7;
const uint8_t ENB = 5;
const uint8_t LINE_LEFT = 8;
const uint8_t LINE_RIGHT = 12;
const int BASE_SPEED = 150; // 0-255: start slow, raise once it tracks well
const int TURN_SPEED = 120;
const bool LINE_IS_HIGH = true; // most TCRT5000 boards output HIGH over black
int lastTurn = 0; // remembers which way the line went
// speed: -255 (full reverse) to 255 (full forward)
void drive(int left, int right) {
digitalWrite(IN1, left >= 0 ? HIGH : LOW);
digitalWrite(IN2, left >= 0 ? LOW : HIGH);
analogWrite(ENA, constrain(abs(left), 0, 255));
digitalWrite(IN3, right >= 0 ? HIGH : LOW);
digitalWrite(IN4, right >= 0 ? LOW : HIGH);
analogWrite(ENB, constrain(abs(right), 0, 255));
}
bool onLine(uint8_t pin) { return (digitalRead(pin) == HIGH) == LINE_IS_HIGH; }
void setup() {
Serial.begin(115200);
pinMode(ENA, OUTPUT); pinMode(IN1, OUTPUT); pinMode(IN2, OUTPUT);
pinMode(ENB, OUTPUT); pinMode(IN3, OUTPUT); pinMode(IN4, OUTPUT);
pinMode(LINE_LEFT, INPUT);
pinMode(LINE_RIGHT, INPUT);
drive(0, 0);
delay(2000); // two seconds to put it down on the track
}
void loop() {
bool left = onLine(LINE_LEFT);
bool right = onLine(LINE_RIGHT);
if (!left && !right) {
drive(BASE_SPEED, BASE_SPEED); // line between the sensors: straight on
} else if (left && !right) {
drive(-TURN_SPEED / 2, TURN_SPEED); // line drifting left: turn left
lastTurn = -1;
} else if (!left && right) {
drive(TURN_SPEED, -TURN_SPEED / 2); // line drifting right: turn right
lastTurn = 1;
} else {
// both sensors on black: junction or lost, keep turning the last way
if (lastTurn < 0) drive(-TURN_SPEED, TURN_SPEED); else drive(TURN_SPEED, -TURN_SPEED);
}
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The ENA/ENB jumpers must be removed and wired to PWM pins, and the battery GND must connect to the board GND.
Swap that motor's two wires on the screw terminal.
Lower the sensor to 5–10 mm from the surface and re-tune the trimmer until its LED switches between the light and dark surface.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
10 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, L298N Dual H-Bridge Motor Driver Module, TCRT5000 Dual Channel Line Tracking Sensor Module, 2WD Smart Robot Car Chassis Kit, 2 × 18650 Battery Holder, 2 × 18650 Li-ion Rechargeable Cell 2600mAh, MT3608 Mini Boost Converter Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter, Precision Screwdriver Set and Soldering Station. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 3–4 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (line_follower_robot.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,170 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
H-bridges and PWM speed control; Infrared reflectance sensing.
Ideas that reuse this build: Obstacle-avoiding robot, Bluetooth-controlled car and Table-edge avoider. They are listed under Take it further on this page.
A robot that looks left and right with its ultrasonic "head" and picks the clearest way.
Roams a tabletop without ever driving off the edge.
Drive a 4WD car from your Android phone over Bluetooth.
Four knobs, four servos: pick things up with a desktop robot arm.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.