Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsThe classic memory game on a breadboard. Each light has its own note; the Uno plays a sequence and you copy it with the three buttons. Get it right and the sequence grows by one and speeds up; get it wrong and a low buzz tells you which level you reached.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Three momentary buttons, one leg each to a pin and the other legs joined to GND; the internal pull-ups do the rest.
Three indicator LEDs, each through a 330 Ω resistor to its pin.
Follow the colours: red is power, dark grey is ground, blue is a signal.
simon_memory_game.inoVerify & upload in Electrolark// Simon memory game
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "simon-memory-game"
// ---- pins ----
const uint8_t BTN_1 = 2;
const uint8_t BTN_2 = 3;
const uint8_t BTN_3 = 4;
const uint8_t LED_RED = 5;
const uint8_t LED_YELLOW = 6;
const uint8_t LED_GREEN = 7;
const uint8_t PIEZO_PIN = 8;
int sequence[32], level = 0;
const int NOTES[4] = {0, 262, 330, 392}; // C4, E4, G4 for buttons 1-3
// returns 0 when nothing is pressed, else 1-3
int pressedButton() {
if (digitalRead(BTN_1) == LOW) return 1;
if (digitalRead(BTN_2) == LOW) return 2;
if (digitalRead(BTN_3) == LOW) return 3;
return 0;
}
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setYellowLed(bool on) { digitalWrite(LED_YELLOW, on ? HIGH : LOW); }
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void setLed(int n, bool on) { if (n == 1) setRedLed(on); else if (n == 2) setYellowLed(on); else setGreenLed(on); }
void flash(int n, int ms) {
setLed(n, true); tone(PIEZO_PIN, NOTES[n]);
delay(ms);
setLed(n, false); noTone(PIEZO_PIN);
delay(120);
}
int waitForPress(unsigned long timeoutMs) {
unsigned long t = millis();
while (millis() - t < timeoutMs) {
int p = pressedButton();
if (p) { flash(p, 200); while (pressedButton()) delay(5); return p; }
}
return 0;
}
void fail() {
tone(PIEZO_PIN, 120, 600);
for (int k = 0; k < 3; k++) { setLed(1, true); setLed(2, true); setLed(3, true); delay(150); setLed(1, false); setLed(2, false); setLed(3, false); delay(150); }
Serial.print(F("You reached level ")); Serial.println(level);
level = 0;
delay(1000);
}
void setup() {
Serial.begin(115200);
pinMode(BTN_1, INPUT_PULLUP); pinMode(BTN_2, INPUT_PULLUP); pinMode(BTN_3, INPUT_PULLUP);
pinMode(LED_RED, OUTPUT); pinMode(LED_YELLOW, OUTPUT); pinMode(LED_GREEN, OUTPUT);
randomSeed(analogRead(A3));
}
void loop() {
if (level == 0) { // wait for any button to start
if (!pressedButton()) return;
while (pressedButton()) delay(5);
delay(500);
}
sequence[level] = random(1, 4);
level++;
for (int i = 0; i < level; i++) flash(sequence[i], max(150, 500 - level * 25));
for (int i = 0; i < level; i++) {
int p = waitForPress(4000);
if (p != sequence[i]) { fail(); return; }
}
Serial.print(F("Level ")); Serial.print(level); Serial.println(F(" done"));
delay(700);
if (level >= 31) { Serial.println(F("You win!")); level = 0; }
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
It is rotated 90°; turn it so the legs span the gap.
It is backwards: the long leg goes to the resistor.
Normal for a bare piezo; mount it on a small box to resonate.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, 3 × Tactile Push Button Switch, Through-Hole LED Pack (Pack of 10), Piezo Buzzer (passive), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (simon_memory_game.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹405 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Arrays and random sequences; Reading several buttons; Playing notes with tone().
Ideas that reuse this build: Whack-a-mole with a score display and Quiz buzzer for three teams. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.