Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsThe classic first sequencing project. Lights run green, amber, red, red-and-amber, with timings you can change. Press the pedestrian button and the green phase is cut short, with a chirp when it is safe to cross.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Red indicator LED for the alert state.; Yellow indicator LED.; Green indicator LED for the normal state.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
traffic_light_model.inoVerify & upload in Electrolark// Traffic light with pedestrian button
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "traffic-light-model"
// ---- pins ----
const uint8_t LED_RED = 2;
const uint8_t LED_YELLOW = 3;
const uint8_t LED_GREEN = 4;
const uint8_t BUTTON_PIN = 5;
const uint8_t BUZZER_PIN = 6;
bool walkRequested = false;
const unsigned long GREEN_MS = 8000, YELLOW_MS = 2000, RED_MS = 6000;
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setYellowLed(bool on) { digitalWrite(LED_YELLOW, on ? HIGH : LOW); }
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void lights(bool r, bool y, bool g) { setRedLed(r); setYellowLed(y); setGreenLed(g); }
void waitWatching(unsigned long ms) {
unsigned long t = millis();
while (millis() - t < ms) { if (digitalRead(BUTTON_PIN) == LOW) walkRequested = true; }
}
void setup() {
Serial.begin(115200);
pinMode(LED_RED, OUTPUT);
pinMode(LED_YELLOW, OUTPUT);
pinMode(LED_GREEN, OUTPUT);
pinMode(BUTTON_PIN, INPUT_PULLUP);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
}
void loop() {
lights(false, false, true);
waitWatching(walkRequested ? 2000 : GREEN_MS); // a waiting pedestrian shortens green
lights(false, true, false);
waitWatching(YELLOW_MS);
lights(true, false, false);
if (walkRequested) { setBuzzer(true); delay(80); setBuzzer(false); } // "you may cross" chirp
walkRequested = false;
waitWatching(RED_MS);
lights(true, true, false); // red + amber before green
waitWatching(1000);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, 3 × Through-Hole LED Pack (Pack of 10), Tactile Push Button Switch, Active Buzzer Module 3.3–5V, Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 10 steps.
No. This page has the complete, tested code (traffic_light_model.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹434 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Pull-ups and debouncing.
Ideas that reuse this build: Reaction game. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.