LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe price-computing scale every vegetable vendor uses, built from a load cell, a keypad and an LCD. Type the rate per kilogram and press #; the top line shows the weight and rate, the bottom line the price in rupees. D zeroes the scale with an empty tray. A good project for learning how load cells, keypads and maths come together.
A learning project. Scales used for trade in India must be stamped by the Legal Metrology department, which this is not.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
A strain-gauge bar that bends very slightly under load, and a 24-bit HX711 amplifier that turns that into a weight.
16-key membrane keypad scanned as a 4×4 grid, so 8 wires read 16 buttons.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
vegetable_price_scale.inoVerify & upload in Electrolark// Price-computing scale for vegetable and kirana shops
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "vegetable-price-scale"
#include <HX711.h>
#include <Keypad.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t HX_DT = 2;
const uint8_t HX_SCK = 3;
const uint8_t KP_R1 = 4;
const uint8_t KP_R2 = 5;
const uint8_t KP_R3 = 6;
const uint8_t KP_R4 = 7;
const uint8_t KP_C1 = 8;
const uint8_t KP_C2 = 12;
const uint8_t KP_C3 = 13;
const uint8_t KP_C4 = 9;
HX711 scale;
const float CALIBRATION = 420.0; // raw units per gram: calibrate with a known weight
const char KEYS[4][4] = {{'1','2','3','A'},{'4','5','6','B'},{'7','8','9','C'},{'*','0','#','D'}};
byte rowPins[4] = {KP_R1, KP_R2, KP_R3, KP_R4};
byte colPins[4] = {KP_C1, KP_C2, KP_C3, KP_C4};
Keypad keypad = Keypad(makeKeymap(KEYS), rowPins, colPins, 4, 4);
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float grams = 0;
long ratePerKg = 0; // price per kg in rupees, typed on the keypad
long typing = 0;
bool editing = false;
unsigned long lastRead = 0;
void setup() {
Serial.begin(115200);
scale.begin(HX_DT, HX_SCK);
scale.set_scale(CALIBRATION);
scale.tare(); // empty platform = 0 g
lcd.init();
lcd.backlight();
lcd.print(F("Type rate, #"));
}
void loop() {
char k = keypad.getKey();
if (k >= '0' && k <= '9') { editing = true; typing = min(99999L, typing * 10 + (k - '0')); }
else if (k == '#') { if (editing) ratePerKg = typing; editing = false; typing = 0; } // # confirms the rate
else if (k == '*') { editing = false; typing = 0; } // * cancels typing
else if (k == 'D') { scale.tare(); Serial.println(F("Tared")); } // D = zero with the empty tray on
if (millis() - lastRead < 300) return;
lastRead = millis();
grams = scale.get_units(5);
if (grams < 0) grams = 0;
char buf[17];
lcd.setCursor(0, 0);
if (editing) snprintf(buf, sizeof(buf), "Rate: %-10ld", typing);
else { snprintf(buf, sizeof(buf), "%5d g %4ld/kg ", (int)grams, ratePerKg); }
lcd.print(buf);
float price = grams / 1000.0f * ratePerKg;
lcd.setCursor(0, 1); lcd.print(F("Rs ")); lcd.print(price, 2); lcd.print(F(" "));
Serial.print(grams, 0); Serial.print(F(" g, Rs ")); Serial.println(price, 2);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Let it warm up for a minute and avoid touching the wires; re-tare after warm-up.
Place a known weight and adjust CALIBRATION until the reading matches.
Rows and columns are swapped or reversed; swap the rowPins and colPins lists.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, 5kg Load Cell Kit with HX711 Module, Membrane Matrix Keypad (4x4), LCD1602 16x2 Character LCD (blue, with I2C adapter), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (vegetable_price_scale.ino). Install these libraries first: HX711, Keypad and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹979 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Character displays and I²C backpacks; Matrix scanning; Strain gauges, amplifiers and calibration factors.
A learning project. Scales used for trade in India must be stamped by the Legal Metrology department, which this is not.
Ideas that reuse this build: Kitchen scale and Parts-counting scale. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
0 g, Rs 0.00 0 g, Rs 0.00 1 g, Rs 0.00 1 g, Rs 0.00 1 g, Rs 0.00 0 g, Rs 0.00 0 g, Rs 0.00 1 g, Rs 0.00
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.