LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsBusy days at a desk or in a hot workshop make it easy to forget water. The bottle stands on a small load-cell coaster. Every time it gets at least 20 g lighter, the Nano counts it as a drink and restarts the timer. After 45 minutes without a sip, the green light goes out and the buzzer chirps until you drink.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
A strain-gauge bar that bends very slightly under load, and a 24-bit HX711 amplifier that turns that into a weight.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
water_bottle_drink_reminder.inoVerify & upload in Electrolark// Water bottle drink reminder coaster
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "water-bottle-drink-reminder"
#include <HX711.h>
// ---- pins ----
const uint8_t HX_DT = 2;
const uint8_t HX_SCK = 3;
const uint8_t LED_GREEN = 4;
const uint8_t BUZZER_PIN = 5;
HX711 scale;
const float CALIBRATION = 420.0; // raw units per gram: calibrate with a known weight
// ---- latest readings ----
float grams = 0;
const unsigned long REMIND_MS = 45 * 60000UL; // remind after 45 minutes without a sip
const float SIP_G = 20; // a drop of at least this many grams counts as a drink
float lastWeight = 0;
unsigned long lastSip = 0, lastRead = 0;
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
scale.begin(HX_DT, HX_SCK);
scale.set_scale(CALIBRATION);
scale.tare(); // empty platform = 0 g
pinMode(LED_GREEN, OUTPUT);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
lastWeight = scale.get_units(5); lastSip = millis();
}
void loop() {
if (millis() - lastRead < 2000) return;
lastRead = millis();
grams = scale.get_units(5);
if (grams < 30) { setBuzzer(false); setGreenLed(false); return; } // bottle lifted off: wait for it to come back
if (lastWeight - grams > SIP_G) { lastSip = millis(); Serial.print(F("Drank ")); Serial.print(lastWeight - grams, 0); Serial.println(F(" g")); }
lastWeight = grams;
bool due = millis() - lastSip > REMIND_MS;
setGreenLed(!due);
setBuzzer(due && (millis() / 1000) % 20 == 0); // a short chirp every 20 seconds until you drink
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Let it warm up for a minute and avoid touching the wires; re-tare after warm-up.
Place a known weight and adjust CALIBRATION until the reading matches.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), 5kg Load Cell Kit with HX711 Module, Through-Hole LED Pack (Pack of 10), Active Buzzer Module 3.3–5V, Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (water_bottle_drink_reminder.ino). Install this library first: HX711.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹826 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Strain gauges, amplifiers and calibration factors.
Ideas that reuse this build: Kitchen scale and Posture reminder. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.