LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsWorn on a collar or shirt pocket, the IMU reads the tilt of your upper body. Lean forward more than 25 degrees and the coin motor gives a gentle buzz; sit back up and it stops. The yellow LED shows the state while you tune the angle.
Tick anything you already have and the total updates.
Ten-degree-of-freedom board whose MPU6050 gives acceleration and rotation on three axes; at rest it reads gravity, so it knows how it is tilted.
Follow the colours: red is power, dark grey is ground, blue is a signal.
posture_reminder.inoVerify & upload in Electrolark// Posture reminder clip
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "posture-reminder"
#include <Wire.h>
#include <Adafruit_MPU6050.h>
#include <Adafruit_Sensor.h>
// ---- pins ----
const uint8_t VIBE_PIN = 2;
const uint8_t LED_YELLOW = 3;
Adafruit_MPU6050 mpu;
sensors_event_t accEvt, gyrEvt, tmpEvt;
// ---- latest readings ----
float pitchDeg = 0;
float rollDeg = 0;
float shakeG = 0;
const unsigned long READ_EVERY_MS = 500;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 25; // slouching tips the chest forward by 20-30 degrees
const float HYSTERESIS = 8; // gap that stops rapid on/off switching
void readImu() { mpu.getEvent(&accEvt, &gyrEvt, &tmpEvt); }
float pitchDegNow() { return atan2(accEvt.acceleration.x, sqrt(accEvt.acceleration.y * accEvt.acceleration.y + accEvt.acceleration.z * accEvt.acceleration.z)) * 57.3f; }
float rollDegNow() { return atan2(accEvt.acceleration.y, accEvt.acceleration.z) * 57.3f; }
float shakeGNow() { float a = sqrt(accEvt.acceleration.x * accEvt.acceleration.x + accEvt.acceleration.y * accEvt.acceleration.y + accEvt.acceleration.z * accEvt.acceleration.z) / 9.81f; return fabs(a - 1.0f); }
void setVibe(bool on) { digitalWrite(VIBE_PIN, on ? HIGH : LOW); }
void setYellowLed(bool on) { digitalWrite(LED_YELLOW, on ? HIGH : LOW); }
void evaluate() {
if (!alertOn && pitchDeg > ALERT_LEVEL) alertOn = true;
else if (alertOn && pitchDeg < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "Sit up" : "Good posture";
}
void setup() {
Serial.begin(115200);
if (!mpu.begin()) Serial.println(F("MPU6050 not found on the GY-87"));
mpu.setAccelerometerRange(MPU6050_RANGE_4_G);
mpu.setFilterBandwidth(MPU6050_BAND_21_HZ);
pinMode(VIBE_PIN, OUTPUT);
pinMode(LED_YELLOW, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
pitchDeg = (readImu(), pitchDegNow());
rollDeg = rollDegNow();
shakeG = shakeGNow();
evaluate();
Serial.print(F("Pitch="));
Serial.print(pitchDeg, 1);
Serial.print(F("deg"));
Serial.print(F(", Roll="));
Serial.print(rollDeg, 1);
Serial.print(F("deg"));
Serial.print(F(", Shake="));
Serial.print(shakeG, 2);
Serial.print(F("g"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setVibe(alertOn);
setYellowLed(alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA/SCL are not swapped and that VCC_IN (not 3.3V) is used for 5 V boards. Run an I²C scanner: it should show 0x68.
Add a 100 nF capacitor across VCC_IN and GND and keep I²C wires under 20 cm.
Check the transistor orientation (flat face: C-B-E for BC547).
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Nano CH340 Development Board (Soldered), GY-87 10DOF Module (MPU6050 + HMC5883L + BMP180), Coin Vibration Motor 3V, Through-Hole LED Pack (Pack of 10), General Purpose Transistors (Pack), Diodes (Pack of 10, 1N4007), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1 hour. The build on this page has 9 steps.
No. This page has the complete, tested code (posture_reminder.ino). Install these libraries first: Adafruit MPU6050 and Adafruit Unified Sensor.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹820 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Accelerometers, gyros and tilt angles; Current-limiting resistors for LEDs; Transistors as switches.
Ideas that reuse this build: Digital spirit level and Step counter. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
0.0deg, Shake=0.00g, status=Good posture Pitch=0.0deg, Roll=0.0deg, Shake=0.00g, status=Good posture Pitch=0.0deg, Roll=0.0deg, Shake=0.00g, status=Good posture Pitch=0.0deg, Roll=0.0deg, Shake=0.00g, status=Good posture
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.