Shop by category
Shop all componentsPower, batteries & solar
A PWM controller pulls the panel down to the battery voltage, so a panel with a higher Vmp than the battery loses that extra power. An MPPT controller converts it into extra charging current, which pays off above about 150 W or when the panel voltage is well above the battery voltage. The 0.85 factor covers heat, dust and wiring losses.
PWM current ≈ panel Imp = W ÷ VmpMPPT current ≈ W × 0.95 ÷ VchargeController A = charging current × 1.25 (PWM: Isc × 1.25)Energy needed = Ah × V × discharge ÷ charge efficiencyDaily energy = charging W × sun hours × 0.85A 100 W panel (Vmp 18 V, Isc 6.1 A) on a 12 V 40 Ah lead-acid battery: MPPT gives 100 × 0.95 ÷ 13.6 = 7 A, so a 10 A MPPT controller. PWM gives only 100 ÷ 18 = 5.6 A, worth 76 W. Refilling half the battery needs 40 × 12 × 0.5 ÷ 0.85 = 282 Wh, about 3.5 sun hours with MPPT.
The charge controller sits between the solar panel and the battery. It stops the battery overcharging and, with an MPPT type, gets the most power out of the panel. Its current rating must cover the charging current with some margin, because panels can briefly produce more than their rating on cold, bright days.
PWM controllers are cheap and fine when the panel voltage suits the battery, such as a 36-cell panel on a 12 V battery. MPPT controllers cost more but harvest 15 to 30% more energy, more again in cold weather or with higher-voltage panels in series.
On a 12 V battery, about 7 A from an MPPT, so a 10 A controller. For PWM, size from the panel’s Isc × 1.25, also about 10 A for a typical 100 W panel.
Under about 100 W the gain is small and a PWM controller is usually fine. MPPT pays off with bigger arrays, higher-voltage panels, panels wired in series, or in cold weather.
With an MPPT controller, yes, and it will use the extra voltage. With PWM it works but wastes nearly half the panel’s power.
PWM is cheaper and fine when panel voltage matches the battery. MPPT harvests 15 to 30 % more when panel voltage is much higher, as with 24 V or 36-cell panels on 12 V batteries.
Charging current × 1.25. For PWM use the panel's short-circuit current × 1.25.
PWM current ≈ panel Imp = W ÷ Vmp; MPPT current ≈ W × 0.95 ÷ Vcharge; Controller A = charging current × 1.25 (PWM: Isc × 1.25); Energy needed = Ah × V × discharge ÷ charge efficiency; Daily energy = charging W × sun hours × 0.85.
A 100 W panel (Vmp 18 V, Isc 6.1 A) on a 12 V 40 Ah lead-acid battery: MPPT gives 100 × 0.95 ÷ 13.6 = 7 A, so a 10 A MPPT controller. PWM gives only 100 ÷ 18 = 5.6 A, worth 76 W. Refilling half the battery needs 40 × 12 × 0.5 ÷ 0.85 = 282 Wh, about 3.5 sun hours with MPPT.
Geekobot builds that use it include Solar pump sunshine switch, Single-axis solar tracker, Solar street light controller and Solar-charged 18650 power bank. Each has the full parts list, wiring and code.
Results are estimates for design and learning. Check critical designs against the component datasheet. Made by the Geekobot Learning Team. How we write our calculators