How-to · Intermediate · 3 min read
Hot Air Rework and SMD Soldering
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
A hot air rework station blows heated air through a nozzle to melt solder on all the pins of a surface-mount part at once. Use it to remove chips, fit QFN and other parts with pads underneath, and reflow solder paste. Start around 300 to 350 °C with low to medium airflow, apply plenty of flux, heat evenly in circles, and lift the part only when every joint has melted.
Key specs at a glance
- Typical settings
- 300 to 350 °C for leaded solder, 350 to 400 °C for lead-free
- Airflow
- Low to medium so small parts do not blow away
- Consumables
- Flux (gel or paste), solder paste, solder wick, Kapton tape
- Nozzles
- Small single nozzles for passives; larger ones for chips
- Combined units
- 2-in-1 stations with a soldering iron and hot air
- Safety
- Hot nozzle and air, flux fumes, never point at people
Removing a part
- 1Cover nearby plastic connectors and small parts with Kapton tape or foil.
- 2Apply flux around the pins.
- 3Hold the nozzle 1 to 2 cm above the part and move it in small circles to heat evenly.
- 4After 20 to 60 seconds, nudge the part gently with tweezers; when it moves freely, lift it straight up.
- 5Clean the pads with flux and solder wick using the iron, then wipe off flux residue with isopropyl alcohol.
Fitting a part with solder paste
- 1Apply a thin, even bead of solder paste on each pad, less than you think, or use a stencil.
- 2Place the part with tweezers, matching pin 1 to the board marking.
- 3Heat from above in circles. The paste turns grey, then shiny, and the part pulls itself into alignment.
- 4Let it cool without moving it.
- 5Check for bridges with a magnifier and a multimeter; remove bridges with flux and a clean iron tip or wick.
Fine-pitch chips with legs (SOIC, TSSOP, QFP) can also be soldered with the iron using drag soldering and lots of flux; parts with pads underneath (QFN, BGA) need hot air or a reflow oven.
Tips and safety
- Pre-heat large boards from below with a pre-heater or a second hot-air pass to avoid warping and lifting pads.
- Too much airflow blows away small resistors; too little heat for too long cooks the board.
- Electrolytic capacitors, plastic connectors and some LEDs and modules melt or burst under hot air; remove or shield them.
- Leave the station to cool down in its cradle; most stations keep the fan running until the element is cool.
- Ventilate: flux fumes are irritating. Wear safety glasses.
Remove and replace an SMD chip with hot air
You need: Flux, Solder paste, Solder wick, Kapton tape, Isopropyl alcohol · Tools: Hot air rework station, Soldering iron, Fine tweezers, Magnifier
Get the parts5 of 5 found in our store · ₹2,50,299
FluxFlux Desktop Laser Cutter (Ador / Beambox / Beamo)₹2,50,000
Solder pasteRMA-223 Solder Flux Paste₹43
Solder wickSolder Wick - Good Quality₹45
Kapton tapePolyimide (Kapton) Tape 33m₹113- Isopropyl alcoholIsopropyl Alcohol (IPA) for PCB Cleaning₹98
- 1ProtectMask nearby heat-sensitive parts with Kapton tape.
- 2Flux and heatApply flux and heat the chip evenly at about 330 °C with medium-low airflow.
- 3LiftLift the chip with tweezers once all solder has melted.
- 4Prepare padsClean the pads with flux and wick, then apply a thin layer of solder paste.
- 5Reflow and inspectPlace the new chip, reflow until it settles, let it cool and check for bridges.
Common mistakes to avoid
- Too much airflow blowing small parts away.
- Lifting a chip before all joints have melted, tearing pads.
- Heating plastic connectors and electrolytic capacitors.
- Using too much solder paste and creating bridges.
- Skipping flux.
Frequently asked questions
What temperature should I use on a hot air station?
Start around 300 to 350 °C for leaded solder and 350 to 400 °C for lead-free, adjusting for board size.
Do I need a hot air station as a beginner?
No. It is useful once you work with surface-mount parts, especially chips with pads underneath.
Can I solder SMD parts with just an iron?
Yes for resistors, capacitors and chips with legs, using flux and a fine tip. Parts with hidden pads need hot air.
Why do my SMD parts blow away?
Airflow is too high or the nozzle is too close. Lower the airflow and move in circles.
How do I fix solder bridges?
Add flux and drag a clean iron tip across the pins, or use solder wick.
Parts for this guide
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



